BENEKOV K14 Page 30 Operation And Installation Manual Download | Manualshive

Page: 30 / 42

background image

- 30 -

Fig 14 Furnace bearings lubrication - view 1

Fig 15 Furnace bearings lubrication - view 2

1.

Disconnect the power supply to the burner and feeder external cable from the programmer.

2.

Loosen the screws (1) that secure the burner cover - 2 pcs.

3.

Remove the burner cover (2).

4.

Unscrew the locking bolts (4) - 4 pcs.

5.

Carefully remove the flange with drives and fan (8).

6.

Whilst removing the panel (3) remove the spark plug (5) from the housing.

7.

Place the disassembled parts in a safe place taking extra care with the spark plug.

8.

Unscrew the bolts (6).

«
...
28
29
30
31
32
...
»

Summary of Contents for K14











































Reviews:

No comments

Related manuals for K14

Combi 25 Eco Elite

Brand: Main Pages: 12

Brand: Warmhaus Pages: 48

Vitorondens 200-T Series

Brand: Viessmann Pages: 4

Brand: Slant/Fin Pages: 4

Brand: Camus Hydronics Pages: 90

Brand: U.S. Boiler Company Pages: 52

Multidea Evo 100

Brand: Bongioanni Pages: 64

Brand: UTICA BOILERS Pages: 48

Brand: Viadrus Pages: 56

Brand: HDG Pages: 80

Brand: Weil-McLain Pages: 68

Brand: Weil-McLain Pages: 128

Brand: Unical Pages: 44

INDEPENDENCE IN10 CANADA

Brand: Burnham Pages: 1

Brand: Adarad Pages: 22

Estelle B4 INOX ErP

Brand: Sime Pages: 88

Brand: Southbend Pages: 45

Brand: IDEAL Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands