manualshive.com logo in svg

BendPak R76LT, Technical Service Bulletin

Share
Download
BendPak R76LT Technical Service Bulletin Download Page 8

 

R76LT Installing the Tilt Tower  

 

Page 8 of 9    

 

BendPak TSB 82-092021 

 

⚠

 

WARNING

 

Clear everything off the Turntable, and out of the path of the Tilt Tower 

prior

 to 

connecting the Tire Changer to pressurized air. 

⚠

 

WARNING

 

Stay clear of pinch points and moving components. Once Air Pressure is provided to 
the Tire Changer the Tilt Tower will return to its upright position and the Wheel Clamps 

on the Turntable will move to the outside of the Turntable. 

5.

 

Connect to air source 140-165 PSI (10-11 BAR) maximum. Be aware of moving components; stay 
clear of pinch points.

 

6.

 

Replace the Service Access panel (seven M6 Machine Screws).

 

7.

 

Remove the Air Regulator and Oiler to provide installation clearance for the plastic Tilt Tower Base 
Cover.

 

8.

 

Install the Tilt Tower Base Cover (M6 Phillips Machine Screw).

 

 

9.

 

Install Air Regulator and Oiler. 

10.

 

Install back cover (two Hex Nuts). 

 
 
 
 
 

 
 

 

 

Summary of Contents for R76LT










Reviews:

No comments

Brands by name

Popular brands

Load more brands