background image

5

cause a drop in line voltage resulting in loss
of power and overheating. The following
table shows the correct size to use
depending on cord length and nameplate
ampere rating. If in doubt, use the next
heavier gage. The smaller the gage number,
the heavier the cord.

Minimum Gage for Cord Sets

Volts

Total Length of Cord in Feet

120V

0-25

26-50

51-100 101-150

240V

0-50

51-100 101-200 201-300

Ampere Rating
More Not more

AWG

Than Than

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10 -

12

16

16

14

12

12 -

16

14

12

Not Recommended

OUTDOOR USE EXTENSION CORDS.
When tool is used outdoors, use only
extension cords intended for use outdoors
and so marked.

STAY ALERT. Watch what you are doing.
Use common sense. DO NOT OPERATE
TOOL when you are tired or otherwise
impaired.

CHECK DAMAGED PARTS. Before using
the tool, during and after the operation of
tool, always check carefully for damaged
parts, the alignment of moving parts,
breakage of parts, mounting, and any other
conditions that may affect its safe operation.
If a guard or any other part is damaged,
return the tool to your local Kmart for a free
replacement (applies for duration of
warranty, see WARRANTY section at the
front of this manual).

USE OF ACCESSORIES AND
ATTACHMENTS
. The use of any accessory
or attachment not recommended for use
with the tool could be hazardous. 

GENERAL SAFETY RULES (FOR ALL TOOLS)

SAFETY WARNINGS AND INSTRUCTIONS: 

DOUBLE INSULATION

Double insulated tools are constructed throughout with two separate layers of electrical insula-
tion or a double thickness of insulation between you and the tool’s electrical system. Tools built
with double insulation are not intended to be grounded. As a result, your tool is equipped with a
two prong plug which permits you to use extension cords without concern for maintaining a
ground connection.
Double insulation does not take the place of normal safety precautions when operating this
tool. The insulation system is for added protection against injury resulting from a possible elec-
trical insulation failure within the tool. The insulation system is for added protection against
injury resulting from a possible electrical insulation failure within the tool.

WARNING: 

The operation of any power tool can result in for-

eign objects being thrown into your eyes, which can result in severe
eye damage. Before beginning power tool operation, we recommend
wearing safety goggles or safety glasses with side shield and a full face
shield, if needed.

607691-00/BT300 Sander  11/3/03  3:14 PM  Page 5

Summary of Contents for BENCHTOP 607691-00

























Reviews: