Details of Programming
14
Alamp
Alamp On
(alert lamp on)
In this setting, the backlit VOLUME/MUTE
will flash on and off during an alert.
AlampOFF
(alert lamp off)
In this setting, the VOLUME/MUTE backlit
button will not flash on and off during an
alert.
Voice
Voice On
(Voice announcements on)
In this setting, all radar, laser, and SWS
messages (if programmed) will be
announced using a digital voice.
Voice Off
(Voice announcements off)
In this setting, only the distinct audio tone
will be heard when a radar, Laser, or SWS
message is detected.
15
Power-on Sequence
PwrOnSTD
(Standard)
In this setting, each time you turn on the STi
DRIVER, it will display “Bel STi,” “LASER,”
“Ka-band,” “K-band,” “X-band,” followed by
a brief SWS alert. (factory default)
If any of the factory default bands have
been disabled, a double X-band tone and
corresponding message (i.e. “X OFF”), will
alert you that one or more bands have been
turned off.
PwrOnFST
(Fast power-on)
In this setting, the STi DRIVER will provide
a single X-band tone if the factory default
settings have not been changed. If any of
the factory default band settings have been
disabled, a double X-band tone and corre-
sponding message (i.e. “X OFF”), will alert
you that one or more bands have been
turned off.
Signal Strength Meter
MeterSTD
(Standard meter)
In this setting, the meter displays the band
of the received signal, and a bar graph
shows the relative signal strength. (factory
default)
MeterTHT
(Threat Display)
In this setting, the meter will simultaneously
track multiple radar signals, including
relative signal strength for each.
MeterTEC
(Tech Display meter)
In this setting, the meter displays the actual
numeric frequency of the radar signal
received.
AutoMute
aMute ON
(AutoMute on)
In this setting, the STi DRIVER’s audio alerts
will initially be at the volume you set, but
after a few seconds, the STi DRIVER will
automatically reduce the volume level, to
keep you informed, but not annoyed.
(factory default)
aMuteOFF
(AutoMute off)
With AutoMute off, the STi DRIVER’s audio
alerts will remain at the volume you set for
the duration of the radar encounter.
NOTE:
When you are using the Dark
mode, the display will not display
anything. Only the power-on indication
on the SmartPlug will illuminate.
NOTE:
A high or low voltage warning is
given any time the vehicle’s voltage
drops below 10.5 volts, or goes above
16.5 volts. This feature is always on,
regardless of the Pilot setting.
NOTE:
The Tech Display feature is
explained in more detail on page 11.
Display
Disp STD
In this setting, the display will provide all
information in its normal orientation.
Disp INV
In this setting, the detector can be mounted
upside down and all information will be
inverted so it’s readable.
Pilot (Power-on indication)
Pilot HWY
(Full description)
In this setting, the STi DRIVER will display
“Highway,” “AutoScan,” “City,” or “CityNox”
as its power-on indication. (factory default)
Pilot H
(Letter)
In this setting, the STi DRIVER will display
“H” for Highway, “A” for AutoScan,“C” for
City, and “Cnx” for City NoX.
Pilot V
(Vehicle voltage)
In this setting, the STi DRIVER will
continually display “H” for Highway, A” for
AutoScan,“C” for City, and “Cnx” for City
NoX, and the vehicle’s voltage.
F
Standard
Orientation
F
Inverted
Orientation
130.com.ua
Autogood products «130»
