The BELTRONICS STi DRIVER is the most
advanced radar, laser and safety detector
ever designed, and is ready to use right out
of the box with our recommended factory
settings.
The STi DRIVER includes full X, K,
SuperWide Ka, and Safety Warning System
radar capability, front and rear laser
detection, dual LNA (low noise amplifier)
microwave receivers, digital signal
processing (DSP) for superior range and
reduced false alarms, our patented Mute and
AutoMute, audible and visual band alerts,
and all the performance you’d expect from
BELTRONICS.
In addition, the BELTRONICS STi
DRIVER contains the following
revolutionary features:
• Dual LNA (low noise amplifier)
receivers provide the longest possible
warning against all radar threats.
• TotalShield
™
RF Technology provides
the ultimate in undetectability.
• Programmable Alert Lamp provides
additional visual indication of alerts.
• Rugged magnesium case provides
the ultimate protection for your
investment.
• High and low voltage warning is
given any time the vehicle’s voltage
drops below 10.5 volts, or goes
above 16.5 volts.
• Easy-to-use Programming lets you
customize up to 9 features.
• Exclusive AutoScan mode intelligently
reduces unwanted false alarms.
• Ultra-bright text-display provides easy
to read information from any angle.
• Tech Display provides actual
numeric radar frequency for any
radar signal.
• Programmable Bands (on/off).
• Detects and decodes up to 64 Safety
Warning System messages
• Includes new coiled and direct-wire
SmartPlug, which provides a
convenient mute button right on
the plug.
If you’ve used a radar detector before, a
review of the Quick Reference Guide on
pages 4 and 5, and the Programming
information on pages 12 and 13 will briefly
explain the new features.
If this is your first detector, please read
the manual in detail to get the most out of
your BELTRONICS STi DRIVER’s
outstanding performance and innovative
features.
Please drive safely.
Congratulations
Quick Reference Card
1
Programming Details
E
BELTRONICS STi DRIVER
Quick Reference Card
H
Remove card along perforations
H
H
Remove
card
along
perforations
H
An example
Here is how you would turn the STi
DRIVER’s AutoMute feature off.
1
Enter the Program Mode by holding both
the VOLUME/MUTE and SENS buttons
down for 2 seconds. The
STi DRIVER will
beep twice and display
Program
.
2
Then hold the RVW button down.
The
STi DRIVER will scroll through the
categories, starting with display (
Display
),
power-on indication (
Pilot
), then alert
lamp (
Alamp
), Voice, Power-on sequence,
signal strength meter, and then AutoMute.
3
Release the RVW button when the STi
DRIVER shows the AutoMute item.
Since
the factory setting is for AutoMute to be
on, the STi DRIVER will display
aMute ON
.
(If you accidentally don’t release the
Review button in time, and the STi
DRIVER goes to the next category, hold the
RVW button down again, and scroll
through the categories again until
aMute
is displayed.)
4
Press the CHG button to change from
aMute ON
to
aMute OFF
.
5
To complete the Programming, simply
wait 8 seconds without pressing any button.
The STi DRIVER will display
Complete
,
beep 4 times, and return to normal
operation.
There are 9 user-selectable options so you
can customize your STi DRIVER for your
own preferences.
The buttons labeled VOLUME/MUTE
and SENS are also used to enter the Program-
ming Mode, REVIEW your current program
settings, and to CHANGE any settings as
desired. The abbreviations PGM, RVW, and
CHG are located on the lower part of the
display lens and are highlighted in graphics.
How to use Programming
1
To enter Program Mode, press and
hold both VOLUME/MUTE and SENS
buttons down for 2 seconds.
(The unit
will beep twice, and will display the word
“Program”).
2
Then press the RVW button to review
the current settings
. (You can either tap
the button to change from item to item, or
hold the button to scroll through the items).
3
Press the CHG button to change any
setting.
(You can either tap the button to
change from setting to setting, or hold the
button to scroll through all the options).
4
To leave Program Mode, simply wait
8 seconds without pressing any button.
(The unit will display Complete, beep 4
times, and return to normal operation).
Factory Default Settings
To reset the STi DRIVER to its original
factory settings, press and hold the
“VOLUME/MUTE,” and “SENS,” buttons
while turning the power on. The STi
DRIVER’s display will provide a “Reset”
message, accompanied by an audible
alert, acknowledging the reset.
FCC Note:
Modifications not expressly
approved by the manufacturer could
void the user’s FCC granted authority to
operate the equipment.
130.com.ua
Autogood products «130»
