manualshive.com logo in svg

Bellfires Smart Bell Panorama 73/52 MF, Installation And Maintenance Manual, Page: 6 / 44

Share
Download
Bellfires Smart Bell Panorama 73/52 MF Installation And Maintenance Manual Download Page 6

22

Description

2.1

Intended use

The appliance is intended for use in a completely sealed or mechanically ventilated

house without extra ventilation and/or fume extraction to heat the room wherein it is

installed. Do not use it for other purposes.
The appliance may only be used at a location that meets the requirements for the

installation of the appliance. Refer to the preparation manual.

2.2

Installation options

The appliance is supplied with a MF (MagniFire) double burner.

• The appliance can be installed as an insertion into an existing open fireplace or as a

built-in appliance in a new fireplace.

• A mantel iron can be installed on the appliance. The mantel iron makes it possible to

build the brickwork of the fireplace beyond the height of the appliance.

2.3

Overview of a typical installation

Note:
This is an example of a typical installation with a wall outlet for the concentric

flue, your installation can be different.

Item

Description

A Appliance

Decorative gas fire that heats the room

B Control unit

Contains the gas regulator block, receiver and

the fan/light module

Description

6

Smart Bell Panorama 73/52

Summary of Contents for Smart Bell Panorama 73/52 MF













































Reviews:

No comments