Bellfires Smart Bell Panorama 73/52 MF Installation And Maintenance Manual Download Page 18

C

Caution:
• Only use the items that are supplied or described in the preparation

manual and other related documentation.

• Do not use masking tape on the appliance. Masking tape can damage the

finish of the appliance.

• Do not insulate the appliance. If necessary, only install strips of white,

loose insulation wool that is heat resistant up to at least 1000 °C. Install

the insulation strips with a width of maximally 15 cm to protect the walls.

Only install these strips on top and on the side of the appliance.

• Do not use fiberglass, rockwool, or any other sort of insulation material.

These materials produce pungent odour and can produce discolouration of

the fireplace.

• Make sure that brickwork is build with a clearing of at least 3 mm between

the sides and the top of the appliance and the brickwork. The appliance

can expand during operation due to heating.

• Do not build the brickwork higher than the casing without the use of a

mantel iron.

3.3

Safety instructions with regard to the environment

• Dispose of the packing materials in an environmentally friendly way.
• Dispose of batteries as chemical waste.
• Dispose of ceramic heat-resistant glass as household waste. Do not dispose of

ceramic heat-resistant glass in a glass recycling container.

• Dispose of an obsolete appliance according to instructions of the authorities or the

fitter.

• Obey the local regulations.

Safety

18

Smart Bell Panorama 73/52

Summary of Contents for Smart Bell Panorama 73/52 MF













































Reviews: