Bellfires HORIZON BELL SMALLTUNNEL 3 Installation Instructions And Instructions For Use Download Page 75

Page: 75 / 102

Bell

fi res

English

Instructions for use and installation instructions

Note !

•

Small embers and their residue should not be scattered on

the burner. This can cause a blockage on the burner orifi ces.

• Embers and vermiculite granules must not be placed next to

the pilot light burner.

• Important: make sure that all burner openings remain free !!

Burner orifi ces, which are not open, could lead to a dangerous

situation.

4 Place the logs on the burner:

Appliance

Natural gas-burner

Propane / Butane-burner

see fi gure:

Derby 3

Keep the burner orifi ces unblocked

!!!

5 Place the chips of wood around the burner.

Summary of Contents for HORIZON BELL SMALLTUNNEL 3







































































































Search results

Summary of Contents for HORIZON BELL SMALLTUNNEL 3

Reviews:

Related manuals for HORIZON BELL SMALLTUNNEL 3

Brands by name

Popular brands

Bellfires HORIZON BELL SMALLTUNNEL 3, Installation Instructions And Instructions For Use

Search results

Summary of Contents for HORIZON BELL SMALLTUNNEL 3

Reviews:

Related manuals for HORIZON BELL SMALLTUNNEL 3

Brands by name

Popular brands