background image

8

The temperature indicator light will cycle on and off during use 

to regulate the temperature.  

Warning: Never leave the iron’s ceramic soleplate resting on 

fabric for any longer than 15 seconds.  

If ironing with steam for prolonged periods of time, it is 

advisable to use the iron as a corded unit. 

Ironing without Steam

For removing creases from more sensitive fabrics, try ironing without steam. 

STEP 1: Press the steam control trigger until the steam setting indicator is set to ‘0’. 

STEP 2: Plug in and switch on the iron at the mains power supply. 

STEP 3: To increase the temperature of the iron, rotate the temperature control dial in 

a clockwise direction until the desired heat setting is selected. Reduce the temperature 

by rotating the temperature control dial in an anticlockwise direction. The temperature 

indicator light will illuminate to indicate that the iron is heating up; this will switch off 

once the iron is ready to use. 

STEP 4: Test the iron on a small area of the fabric to check that the selected temperature 

is suitable; adjust if necessary. 

STEP 5: After use, rotate the temperature control dial to the ‘Off’ position. Switch off and 

unplug the iron from the mains power supply and allow to cool thoroughly. 

If ironing with steam for prolonged periods of time, it is advisable to use the iron as a 

corded unit.

Steam Burst Function

For creases that are stubborn and difficult to remove, use the steam control trigger to 

select the desired steam setting; if necessary, press the steam burst button for extra 

steam. Wait approx. 5 seconds in-between each burst to prevent any water leaking out 

from the steam holes.

Note: The iron will only produce steam when the temperature 

control dial is set to the 3-dot heat setting.

Vertical Steam Ironing

The steam burst button can also be used to vertically steam curtains and other 

hanging garments. 

STEP 1: Hang up the item to be vertically steamed.  

STEP 2: Press the steam control trigger until the steam setting indicator is set to ‘0’. 

STEP 3: Fill the water tank following the instructions in the section entitled ‘Filling the 

Water Tank’. 

Summary of Contents for BEL0747

















Reviews: