Bedder Way ECONOMY MELAMINE MURPHY BED Installation Instructions Manual Download Page 22 | Manualshive

Page: 22 / 30

Bedder Way ECONOMY MELAMINE MURPHY BED Installation Instructions Manual Download Page 22

22 of 30

d.

Next, plug the male end of the light into the female end of the wire exiting the Transformer.
Make sure these are completely together before continuing.

e.

PLEASE NOTE

: The Transformer is installed in such a way as to minimize extra wire from

sticking above the Header once the bed is installed.  Therefore, the wires coming out of and
going into the Transformer may appear to be reversed.  This is NOT the case; simply plug the
wires into its proper match.

Figure C

f

. Plug the Power Cord into an outlet.

If necessary, use an extension cord to reach the nearest

outlet.

This is also a good time to test the lights to ensure they are working properly. Also, make

sure that no wires are being pinched at any location. With the lights plugged in and completely
connected, and while the bed is still lying flat on the floor, test the lights by touching the Touch-
pad located on top of the headboard. (

Figure B

). If the lights do not come on, please re-check all

connection and make sure your outlet is not controlled by your rooms light switch

«
...
20
21
22
23
24
...
»

Summary of Contents for ECONOMY MELAMINE MURPHY BED































Reviews:

No comments