2
3
A)
B)
C)
D)
E)*
F)*
G)
‡
parts list
disclaimers
TOLERANCE
All Ergomotion adjustable foundations, depending on make and model,
are designed and manufactured to perform and function within designated
quality control parameters. Bases are subject to meticulous and rigorous
inspections during the quality control process to ensure bases will operate
within these standards during
normal operating use. Normal
operating use is defined as the
following: Adjustable foundation is
to be operated with a mattress and
load. Testing procedures require
lifetime cycle tests with up to
120kg distributed load. The angle
(designated “a” in figure 1) between
the back section and the flat
section for various configurations
of the mattress support platform
shall be ± 3°, which translates to a
tolerance of up to 1 ½”.
The angle (designated “B” in figure 1) between the flat section and foot
section for various configurations of the mattress support platform shall be ±
3°, which translates to a tolerance of up to ¾”.
Any adjustable foundation deemed to be within these allocated tolerances is
considered to have met the manufacturer’s quality control standards.
THAT “NEW PRODUCT” SMELL:
Some people notice a slight odor to their new adjustable base—this can
come from our material manufacturing process. This smell is normal and
usually disappears before the product reaches you. Sometimes, however,
this smell may still be noticeable. It usually disappears after a few weeks,
providing adequate ventilation of the product and the environment.
BREAK IN PERIOD:
You can speed up the break-in period by simply spending time in the
adjustable bed through activities such as reading, watching TV or playing
with the kids or grandkids. The extra movement will help the adjustable
base respond to weight and temperature changes. Some of the materials
in our adjustable bases such as the woods, metals and plastics used in the
platform, frame and components are sensitive to moisture content and
temperature and may make sounds in colder environments.
PAIRED OPERATION:
When operating a “paired” split base setup there may be a time latency up
to 1.5 seconds between each bases articulation.
WEAR AND TEAR:
Wear and tear is damage that naturally and inevitably occurs as a result of
normal use or aging.
FABRIC CARE:
To prolong the life of your fabric, protect from direct sunlight whenever
possible. For spot cleaning, wipe area with a light damp sponge or vacuum
with a soft brush attachment to remove particles. Keep at a minimum of
30cm (12 inches) away from direct heat sources. For a deeper cleaning,
blot liquid spills with a clean dry cloth. Wipe with a clean cloth dampened
with warm water. Do not wet excessively. A soft bristle brush may be used
to remove ingrained soil. Avoid scratching by gentle brushing. Wipe with a
clean cloth dampened with warm water to remove residues. Dry in shade
away from direct heat. If persistent marks remain visible after cleaning, seek
professional advice.
PRODUCT RATINGS:
The lift motors are not designed to operate continuously for more than
[2] minutes in an [18] minute time period or approximately 10% duty
cycle. Attempting to circumvent or exceed this rating will shorten the
life expectancy of the product and may void the warranty. The massage
motors are not designed to operate continuously for more than 30 minutes
at a time. Please allow the massaging system to rest for 30 minutes after
automatic massage shut off before restarting.
WEIGHT LIMITS:
This product is not rated to support weights exceeding 850 pounds. This
product is not rated to support weights in excess of 850 pounds inclusive
of the mattress and bedding. The base will structurally support this weight,
provided it is evenly distributed across the bed base. The adjustable base
is not designed to support or lift this amount in the head or foot sections
alone. Exceeding this weight restriction could damage the bed and/or cause
injury and will void the warranty.
IMPORTANT DO’S AND DON’TS
DO:
•
Plug your adjustable base into a power surge protector.
•
Evenly distribute weight when sleeping in a split setup. Uneven
distribution of weight can cause the base to raise unevenly.
•
Call Customer Service for any technical issues. Do not try to force the
base down, this can damage the motors or frame.
•
Use mild soap and water to clean your adjustable base if staining
occurs.
•
Keep in mind that adjustable bases are recommended to be used with
adjustable friendly mattresses
•
Lower to the flat (horizontal) position after use and in between presets.
•
Register your warranty as soon as your adjustable base has been
delivered.
DON’T
•
Sit on corners/edges of base, this may warp the frame, struts or foam.
•
Tilt the base on its side. This can damage the legs and/or leg screws.
•
Stand or jump on the adjustable base at any time, this can damage the
frame and motors.
•
Drag the base to move it. Dragging the base could damage the frame,
strip the nut/bolts or break the legs. Purchase castors if you plan on
moving your base routinely.
•
Enter and exit the adjustable base with the head and/or foot in
the articulated position. Enter or exit your adjustable in the flat
(horizontal) position.
•
Tinker with or modify base. This will void the warranty.
•
Press down on the head or foot while actuated can damage frame
and motors.
FCC Compliance:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
To comply with the FCC RF exposure requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the
device could result in the device exceeding the RF exposure requirement
and void user’s right to operate the device. Radio Frequency: 2.4 GHz
Industry Canada Statement of Compliance:
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device. This device complies with ICES-003 Class B specifications
of Industry Canada.
Actual product appearance and functionality may vary from photographs, illustrations and descriptions included in this manual.
A)
Wireless Remote Control and (3)
AAA batteries
B)
Legs (4)
C)
Power Cord (1)
D)
Power Supply (1)
E)
Power Down Box (1)*
F)
Connecting Strap*
‡
G)
SmartSync™ Cord (1) ‡
Headboard Bracket Components:
H)
Headboard Bracket (2)
I)
T-Bracket (2)
J)
Spacers (2)
K)
Long Bolts (8)
L)
Short Bolts (10)
M)
Nuts (18)
Misc Parts (not included):
N)
Surge Protector (1)
O)
9 Volt Batteries (2)
*
These items are attached to the base for
shipping purposes. Carefully remove from base
and set aside.
‡
Only included in Twin, Twin Long, Queen Split
and Cal King Split bases.
Before discarding the packing materials- ensure all the parts are accounted for.
All electronics and components that need to be installed are located in boxes under the base or attached to the frame.
HEADBOARD BRACKET COMPONENTS
H)
I)
J)
K)
L)
M)
MISC (NOT INCLUDED)
N)
O)
Adjustable
Bed Tolerance
Ergomotion Inc.
|
ph 1-888-550-3746
|
fx 805-979-9399
|
www.ergomotion.
com
All Ergomotion adjustable foundations, depending on make and model, are designed and manufactured to perform and
function within designated quality control parameters. Bases are subject to meticulous and rigorous inspections during
the quality control process to ensure bases will operate within these standards during normal operating use.
Normal operating use is defined as the following:
-Adjustable foundation is to be operated with a mattress and load. Testing procedures require lifetime cycle
tests with up to 120kg distributed load.
The angle (designated “
α
” in figure 1) between the back section and the flat section for various configurations of the
mattress support platform shall be ± 3°, which translates to a tolerance of up to 1 ½”.
The angle (designated “
β
” in figure 1) between the flat section and foot section for various configurations of the mattress
support platform shall be ± 3°, which translates to a tolerance of up to ¾”.
Any adjustable foundation deemed to be within these allocated tolerances is considered to have met the manufacturer’s
quality control standards.
(α°)
(β°)
When operating a "paired" split base setup there may be a time latency up to 1.5 seconds between each bases articulation.
Blake Pettit
Quality Assurance Manager
Ph 805-979-3875
Fx 805-979-9399
www.ergomotion.com