Beast Tek Dirty Glitch v2.0 Assembly Manual Download

Page: 15 / 29

www.beast-tek.com

Dirty Glitch Assembly Manual

| 15

Step 14

Install the two 4.7uf electrolytic capacitors C13 and C14. Install the six 10K ohm resistors R8, R9, R10,

R11, R13 and R14. Solder and trim leads.

NOTE: C17 should not be populated.

Step 15
CAUTION: IC1 and IC2 are sensitive to static discharge (ESD)

Install IC1 and IC2. Take your time to make sure you do not bend any pins. Hold the IC at a 45 degree

angle to the PCB, PARTIALLY insert one row of pins and make sure they are all lined up correctly. Gently

apply even force from the side that is not inserted so that the inserted pins bend slightly so that the non

-inserted side lines up with its socket. Once lined up, apply a small amount of downward force so that

the IC is partially inserted/seated. Double check that all pins are inside their sockets and no pins have

bent outward or inward. Once you are happy everything is lined up, apply force so that the IC is fully

inserted into its socket.

Congratulations, you have finished the main board!! Turn the board over, double check all solder joints,

trim any excessive leads and inspect for missing solder joints.

Summary of Contents for Dirty Glitch v2.0






























Search results

Summary of Contents for Dirty Glitch v2.0

Reviews:

Related manuals for Dirty Glitch v2.0

Brands by name

Popular brands

Beast Tek Dirty Glitch v2.0, Assembly Manual

Search results

Summary of Contents for Dirty Glitch v2.0

Reviews:

Related manuals for Dirty Glitch v2.0

Brands by name

Popular brands