BEARICUDA 6X3 Canterbury Shed Assembly Manual Download

Page: 5 / 14

Page 5

Lift up a

Rear Wall (3)

and orientate the wall as shown above. At the bottom,

align wall siding even with outside of the floor. At the top, align wall siding flush
with framing of side wall. When correctly aligned, attach wall frames together
with

3 - 2 1/2” screws (A)

. Screw on a slight angle to penetrate the side wall

framing best.

Lift Side Wall (2)

up and orientate so

wall framing is flush at rear with floor, wall
siding is flush on side with floor. In the front,
wall framing will overhang the floor as
shown below.

You can find the Square Drive
Bit for the screws in with the
Hardware Kit Bag. (Part B)

Front

Rear

Wall Siding flush with
outside for Floor.

Wall Siding flush with
outside for Floor

3 - 2 1/2” screws
along wall framing

Call 877.232.7428

www.

bearicuda

.com

info

bearicuda

.com

Summary of Contents for 6X3 Canterbury Shed















Search results

Summary of Contents for 6X3 Canterbury Shed

Reviews:

Related manuals for 6X3 Canterbury Shed

Brands by name

Popular brands

BEARICUDA 6X3 Canterbury Shed, Assembly Manual

Search results

Summary of Contents for 6X3 Canterbury Shed

Reviews:

Related manuals for 6X3 Canterbury Shed

Brands by name

Popular brands