background image

We hope your experience constructing our 

6x3 

Canterbury

 

has been both positive and rewarding. We

value your feedback and would like to hear back from you on how well we are doing in the following
areas:

1. Customer Service
2. On Time Shipping
3. Motor Freight Delivery
4. Quality of Materials
5. Assembly Manual
6. Overall Satisfaction.

Please call, write or email us at: 

Bearicuda Inc 3 West St., PO Box 56 Litchfield, CT 06759

 

The materials contained in this Assembly
Manual may be downloaded or copied 
provided that ALL copies retain the 
copyright and any other proprietary notices
contained on the materials. No material
may be modified, edited or taken out of
context such that its use creates a false or
misleading statement or impression as to
the positions, statements or actions.

Congratulations on assembling

your 6x3 

Canterbury

 Storage Shed!

Note;

Our Sheds are shipped as

an unfinished product.  If exposed
to the elements, the western red
cedar lumber will weather to a 
silvery-gray color. If you prefer to
keep the cedar lumber looking 
closer to the original color, we 
suggest that you treat the wood
with a good oil base wood stain.
You may also wish to paint your
new shed rather than stain it.  In
both cases we recommend that
you consult with a paint and stain
dealer in your area for their 
recommendations.

 

Page 14

Call 877.232.7428           

               www.

bearicuda

.com  

                      

           

info

@

bearicuda

.com

The materials contained in this Assembly
Manual may be downloaded or copied 
provided that ALL copies retain the 
copyright and any other proprietary notices
contained on the materials. No material
may be modified, edited or taken out of
context such that its use creates a false or
misleading statement or impression as to
the positions, statements or actions.

6X3 Canterbury Shed 

Summary of Contents for 6X3 Canterbury Shed















Reviews: