background image

6

Manual Manifold

2006230.03

Symbols to BS2971 & ISO 1219-1

Non-return valve

(With gas specific

connection)

Tailpipe

Tailpipe

High pressure cylinders

compete with Isolation

valve

1st stage

regulator

1st stage

relief valve

2nd stage

regulator

Line pressure gauge

Non-return valve

2nd stage

relief valve

Lockable line ball

valve (Valve 'A')

Ball

valve 'C'

Test Point

Alternative supply

source

Medical gas pipeline

distribution system

Exhaust

(piped to safe location)

Lockable line ball

valve (Valve 'B')

Contact

gauge

Sintered

filter

Optional

Bank

Valve

Optional

Bank

Valve

Figure 2 - Schematic Diagram

1.2  Manifold Control Panel

The manifold control panel is supplied as nominally 4 

bar (5 bar max.) and 7 bar (8.5 bar max), (see table 1 

for details).  The 4 bar manifold is available with 100 or 

250 bar contents gauges depending on the pressure 

of the cylinders to be used.  Table 2 shows the supply 

variations.

Option Description

Part Number

Exhaust Pipe Connection Kit

2006233

Termination Box For Remote Alarm

2006219

4 Bar Pressure Switch with Line Contact Monitor

1829936

4 bar Pressure Switch without Line Contact 

Monitor

2000131

7 Bar Pressure Switch with Line Contact Monitor

1829937

7 bar Pressure Switch without Line Contact 

Monitor

2000132

Single Line contact Module

1826618

Double Line contact Module

1826499

1.3  1st Stage Pressure Regulator

For safe operation with regard to performance, 

mechanical strength, resistance to ignition in pure 

high pressure oxygen supply and cleanliness, the 

unit fully conforms to BS EN ISO 10524-2. A pressure 

relief valve connected to the regulator protects the 

downstream pressure and is set at 2000 kPa (20 bar).

Table 2: Manifold Panel, typical cylinder supply 

plus Options

Panel Description

Gas Type

Typical 

Cylinder

Part 

Number

4 bar standard unit (100 

bar Contents Gauge)

N2O

G - 44 bar

2006003

CO2

VF - 50 Bar

4 bar standard unit (250 

bar Contents Gauge)

O2

J - 137 bar

2006004

O2/N2O

J - 137 bar

AIR

J - 137 bar

7 bar standard unit (250 

bar Contents Gauge)

AIR

J - 137 bar

2006005

N2

J - 137 bar

Summary of Contents for Manfiold

























Reviews: