background image

 

 

 

 

 

OPERATION

 

 

1. 

BEFORE

 starting this machine, review the safe instructions in the manual. Failure to follow these rules may result in 

serious injury to the operator or bystanders. 

2. 

NEVER

 leave this machine unattended with the engine running. 

3. 

DO NOT

 operate machine while under the influence of alcohol, drugs, or medication. 

4. 

NEVER

 allow anyone to operate this machine without proper instruction. 

5. 

ALWAYS

 operate this machine with all safety equipment in place and working. Make sure all controls are operating 

properly for safe operation. 

6.  When loading a log, always place your hands on the side of the log, not on the ends, and never use your foot to help 

stabilize a log. Failure to do so, may result in crushed or amputated fingers, toes, hand, or foot. 

7. 

NEVER

 use your foot, a rope or any extension device to operate the control lever on the valve. Only use hand. 

8.  Use only your right hand to operate the controls. 

WARNING!

 When stabilizing log with left hand, remove your hand when the wedge just contacts the log or serious 

injury may occur. 

9.  For logs which are not cut square, the least square end of the log should be placed toward the beam and wedge, and 

the square end placed toward the end plate. 

10.  When splitting in the vertical position, stabilize the log before moving the control handle. Split as follows: 

a.  Place log on the end plate and turn until it leans against the beam and is stable. 
b.  When splitting extra-large or uneven logs, the log must be stabilized with wooden shims or split wood placed   
     between the log and end plate or ground 

11. 

NEVER

 place hands or feet between the log and splitting wedge during forward or reverse stroke as this could result 

in serious injury or death.

 

NEVER attempt to load the log splitter when the ram or wedge is in motion. 

12. 

ALWAYS

 keep fingers away from any cracks that open in the log while splitting. They can quickly close and pinch or 

amputate your fingers. 

13.  Keep your work area clean. Immediately remove split wood around the machine so you do not stumble over it. 
14. 

NEVER

 straddle or step over the log splitter during operation.

 

 

15. 

NEVER

 reach or bend over the log splitter to pick up a log. 

16. 

NEVER try to split two logs on top of each other. NEVER try to cross split a log. 

17. 

NEVER

 operate your log splitter when it is in poor mechanical condition or in need of repair. 

18. 

NEVER

 touch the muffler and other hot areas of the engine during operation. Wait until the engine cools down. 

19. 

NEVER

 tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the 

manufacturer and is within safety limits. Refer to the engine owner’s manual for your particular log splitter. 

20. 

NEVER 

move the log splitter while the engine is running. Shut off the engine if you are leaving the log splitter, even 

for a short period of time. 

21. 

ALWAYS

 be careful when moving or lifting the log splitter. Get assistance if it feels too heavy to move by yourself. 

 
 

 

Page 6

 

 

Summary of Contents for AGRI EASE BE-LS22TL6505GC









































Reviews: