35
TROUBLESHOOTING
Marquee
Bonus
Display not
working
Refer to wiring diagram -
”Marquee & 12 V Wiring”
5 Volt DC power In
is missing.
Communication cable issue.
Pinched, broken, or
disconnected wiring
Faulty board.
Bonus display receives signals and 5 Volt DC power in from
Display Driver Board. (AACE9609)
Display Driver board provides power to, and receives signals
from Rasp Pi Marquee Board.
Check cables from power supply to displays. (AACE6500,
AACE 6533)
Check ribbon cables from display driver to display. (AACE6532)
Check ribbon cables from display driver to Rasp Pi Board
(A5CBL-RBN40-1)
Check power cable from Driver Board to display. (AACE9609)
It could be any of the 3 circuit boards in the system:
Display Board (A5LD1052)
Display Driver Board (AACB9603)
Rasp Pi Marquee Board (AAMBRPI-SQ-M)
Problem
Probable Cause
Remedy
Troubleshooting Guide
Meters do not work
Game counter clicks at
end of each game.
Ticket counter clicks as
tickets come out of game.
The 2 crimped wires may
be faulty
Pinched, broken, or
disconnected wiring
I/O Aux Board faulty.
Inspect crimps on AACO1020 to ensure good connection.
Check connections from counters to main board.
Check continuity on wires.(AACO1020, AACE6514)
Replace I/O Aux Board. (AACB9601-SQ)
Menu Buttons
do not work
Note: If the game
does not coin up,
refer to
Communication
Issues
Game will not enter menu while
game is playing.
Swap connectors at the 2 buttons
Pinched, broken, or
disconnected wiring
Signals are processed on Rasp Pi
Wait until balls are being sorted from tube to press menu
button for right timing.
Replace button if problem stays with button.(AAPB2700)
Inspect crimp to ensure good connection.
Check connections from menu buttons to main board.
Check continuity on AAPB2700, AACE6514
Replace Raspberry Pi. (AAMBRPI-SQ)
Marquee
Bonus not
incrementing
Bonus will
increment when the
game is over.
Menu Setting
Communication cable issue.
Raspberry Pi Board Issue.
Enter the “Payout Settings” menu and ensure the Minimum
value and Maximum value is set correctly.
If the game is at the maximum value, it will not increment higher.
Ensure the phone cable is connected from front I/O Aux board
to the marquee Display Driver Board. (AACE6526, AACE6548,
AACE6531) Check the 2 connector boards. (AACB4051-2)
Make sure phone cables are secure.
Check ribbon cables. (AACE6532 & A5CBL-RBN40-1)
Signals come from Rasp Pi. Replace if needed. (AAMBRPI-SQ)
Dollar Bill
Acceptor
not
working
Ensure bill acceptor has
110 Volts AC.
Dirt or debris in acceptor
slot.
Ensure acceptor dipswitch
is set to “always enable”
Pinched, broken, or
disconnected wiring.
Bill acceptor problem.
Acceptor should cycle stacker at game power up. If not,
check cable connections to power strip.
Caution – 110 Volts AC
Clean with bill reader cleaning card. (A5CC9000)
There are dips on side of acceptor.
Set to “always enable” (not harness enable)
Check wiring from bill acceptor to main board.
Repair or replace wiring harness. (AACE6517)
Refer to troubleshooting section of dollar bill acceptor manual
included with this game or the diagnostics label of the back of the unit.
Summary of Contents for SQUIGGLE
Page 1: ...1 ...