background image

                                                               

                                                

 

A

3

Sport 

User Manual V1.0

http://

www.bay-tec.de                                                                         

3

 / 5                                                            [email protected]

  Delta-wing & V-tail   

Never  use  the  delta-wing  and  V-tail  mixing 

functions of your transmitter, all you need is to 

choose  a  single  4-channel  fixed-wing  model  in 

your radio any time

The right figure shows the 

servo connections for a delta-wing or V-tail.   

 

  Flight Modes   

A3  Supports  4  flight  modes,  including  Normal, 

Auto-balance  ,  Auto-hover  and  Gyro  Off  mode. 

You can switch them using a 3-way switch on the 

transmitter.  But  if  you  are  using  a  2-way  switch 

instead  then  you  can  only  use  2  of  them  during 

flight.  The  color  of  the  LED  shows  you  that  the 

flight  mode  currently  selected,  as  shown  to  the 

right. 

 

A3  allows  you  to  choose  4  kinds  of  mode 

definitions  for  the  3-way  switch,  the  factory 

default  is  Mode-1  (Normal-Balance-Hover).  You 

can  change  it  through  function  7  in  the  setting 

menu, as shown to the right. 
 

  Gyro Directions 

 

It’s  extremely  important  to  verify  that  the  gyros  of  all 

channels  are  reacting in  the  correct  direction  before  flight, 

otherwise  it  could  lead  to  losing  control  or  even  crash 

during  a  flight! 

To  perform  the  examination,  power  on  the 

plane,  pick  it  up  and  check  by  following  the  steps  in  the 

figures  on  the  left.  If  the  gyro  compensates  in  an  incorrect 

direction, reverse it at once! 

 

  Aileron   

  Quickly move the right wing downward around 

the roll axis.  The right aileron  surface should  flap down and 

the left flap up. 

  Elevator 

  Quickly move the nose of the plane downward 

around the pitch axis. The elevator surface should flap up. 

  Rudder   

  Quickly move the nose of the plane to the left 

around the yaw axis. The rudder surface should flap right. 

 

 

 

Flight Mode 

Colors of LED 

Descriptions 

Normal Mode 

Blue 

Gyro rate mode 

Auto-balance 

Red 

Self-balance Mode 

Auto-hover 

Blue & Red 

Self-hover Mode 

Gyro Off Mode 

Off 

Gyro deactivated mode 

 

Modes 

Position-1 

Position-2 

Position-3 

Mode-1 

Normal 

Auto-balance 

Auto-hover 

Mode-2 

Normal 

Gyro Off 

Auto-balance 

Mode-3 

Normal 

Gyro Off 

Auto-hover 

Mode-4 

Auto-balance 

Gyro Off 

Auto-hover 

Summary of Contents for A3X Sport






Reviews: