baxter AK 98 Training Material Download Page 61

Page: 61 / 128

HEMODIALYSIS TREATMENT

| Pause the Treatment

Press the

functions button

to open the functions menu

Press

pause treatment

Select pause with or without blood return and press OK

Follow the instructions on the screen to proceed

To resume the treatment, press the blood pump button to stop
the blood pump

Select connect patient, connect the blood lines to the patient
and press confirm

Press the blood pump button and adjust the blood flow

Press the ultrafiltration button to resume UF removal

When the treatment is paused:

•

The blood flow rate is decreased and the arterial and venous pressure alarm windows are widened

•

The elapsed time in pause is displayed and a sound alarm is triggered every 15 minutes

•

Diascan

measurements, Isolated UF and profiling is disabled

•

Continuous heparinization administration and automatic BPM is deactivated but heparin bolus dose and
manual BPM is enabled

HC10139 |

Summary of Contents for AK 98

































































































































Search results

Summary of Contents for AK 98

Reviews:

Related manuals for AK 98

Brands by name

Popular brands

baxter AK 98, Training Material

Search results

Summary of Contents for AK 98

Reviews:

Related manuals for AK 98

Brands by name

Popular brands