manualshive.com logo in svg

Baumuller b maXX 1000, Parameter Manual

The Baumuller b maXX 1000 is a versatile and high-performance product for industrial automation. To ensure seamless operation, it comes with a comprehensive Parameter Manual, which can be easily downloaded for free from manualshive.com. This manual provides detailed instructions and technical specifications for optimal utilization of the product.

Share
Download
background image

Parameter manual 

b maXX

®

 

1000

Document no. 5.07004.03

205

of 208

Table of figures

Table of figures

Introduction of the device control ...............................................................................................      11
Device control status machine ...................................................................................................      12
Parameter description scheme ..................................................................................................      19
Construction of internal parameter name...................................................................................      19
Controller software version ........................................................................................................      21
Type code ..................................................................................................................................      22
Software version of power unit...................................................................................................      22
V/f curve .....................................................................................................................................      26
Motor PTC overheat protection ..................................................................................................      32
PTC resistor curve .....................................................................................................................      33
Stop method...............................................................................................................................      47
P0805 Line start lockout.............................................................................................................      49
P0805 Line start lockout with external terminals........................................................................      50
Auto energy saving ....................................................................................................................      55
Response delay time..................................................................................................................      59
DIP switch CANopen address....................................................................................................      61
DC braking .................................................................................................................................      63
Base block speed search ...........................................................................................................      65
Momentary power loss operation ...............................................................................................      66
Speed control output frequency limit..........................................................................................      72
Multi function input 2/3-wire .......................................................................................................      75
Position of the control terminals .................................................................................................      76
Accelaration/deceleration time selection....................................................................................      78
Multi step speed .........................................................................................................................      78
Multi function input terminals (internal/external).........................................................................      81
Multi function input terminals (internal/external).........................................................................      81
Extension card terminals............................................................................................................      82
Internal terminal 1 ......................................................................................................................      82
Internal terminal status 2............................................................................................................      83
Extension card 2 ........................................................................................................................      83
Multi function input contact selection 1 ......................................................................................      84
Multi function input contact selection 2 ......................................................................................      84
Display status multi function input terminal 1 .............................................................................      86
Display status external multi function input terminal 2 ...............................................................      86
Display status external multi function input ................................................................................      87
Display status multi function input terminal 1 .............................................................................      87
Display status multi function input terminal 2 .............................................................................      88
Display status multi function input terminal ................................................................................      88
Timing diagram preliminary count value ....................................................................................      91
Brake release frequency ............................................................................................................      92
Display the status of multi function output terminals 1 ...............................................................      93
Display the status of multi function output terminals 2 ...............................................................      93
Output timing chart of multi function terminals ...........................................................................      94
Analog input reference values 1.................................................................................................      95
Analog input reference values 2.................................................................................................      95
ACI/AVI2 selection .....................................................................................................................      96
Voltage/current mode setting .....................................................................................................      99
Analog input reference values 3...............................................................................................      100
Voltage/current mode setting ...................................................................................................      109
Acceleration/deceleration S-curve ...........................................................................................      114
Jog ramp-up/ramp-down time ..................................................................................................      116
Resulting accel/decel time .......................................................................................................      118
Over-voltage stall prevention ...................................................................................................           123
Over-current stall prevention during acceleration ....................................................................      124

Summary of Contents for b maXX 1000



















































































































































































































Reviews:

No comments

Related manuals for b maXX 1000

Planet GT-922 Manual preview
GT-922
Brand: Planet Pages: 7
Perlight Solar PLM-OM Series Installation Manual preview
PLM-OM Series
Brand: Perlight Solar Pages: 19
Allnet ALL-USB-RS422/485 User Manual preview
ALL-USB-RS422/485
Brand: Allnet Pages: 6
Patton electronics 2035-25M User Manual preview
2035-25M
Brand: Patton electronics Pages: 7
Sencore MRD 7000 User Manual preview
MRD 7000
Brand: Sencore Pages: 126
Nightlife SINGLE AUDIO Installation And Testing preview
SINGLE AUDIO
Brand: Nightlife Pages: 12
BZB Gear BG-CAP-HA User Manual preview
BG-CAP-HA
Brand: BZB Gear Pages: 22
Kostal PIKO MP plus Installation Manual preview
PIKO MP plus
Brand: Kostal Pages: 12
Cobra CPI 1550 Operating Instructions Manual preview
CPI 1550
Brand: Cobra Pages: 14
Xantrex 1200, 1750 Owner'S Manual preview
1200, 1750
Brand: Xantrex Pages: 80
TBM MPL020 User Manual preview
MPL020
Brand: TBM Pages: 6
DAYLIFF DG 11000PS Installation & Operating Manual preview
DG 11000PS
Brand: DAYLIFF Pages: 12
DSE RE-BNCRJ1 Owner'S Manual preview
RE-BNCRJ1
Brand: DSE Pages: 2
Wacker Neuson G 3.3AE Operator'S Manual preview
G 3.3AE
Brand: Wacker Neuson Pages: 36
CanadianSolar CSI-5K-S22003-E User Manual preview
CSI-5K-S22003-E
Brand: CanadianSolar Pages: 29
WarmPool OPTIMUS 9 Installation And User Manual preview
OPTIMUS 9
Brand: WarmPool Pages: 37
Video Messenger DV4 H5 Owner'S Manual preview
DV4 H5
Brand: Video Messenger Pages: 25
Buffalo LinkTheater LT-H90LAN User Manual preview
LinkTheater LT-H90LAN
Brand: Buffalo Pages: 59

Brands by name

Popular brands

Load more brands