Baumr-AG PLTCLSBMRAMC2 User Manual Download Page 2

Page: 2 / 19

Cordless Pole Chainsaw

Table of Contents

Safety ......................................................................................................................................................................... 1

General Safety Precautions ........................................................................................................................... 1

Trimming Precautions ................................................................................................................................... 3

Components................................................................................................................................................................ 4

Set-Up .......................................................................................................................................................................... 5

Charging the Battery ..................................................................................................................................... 5

Important Charging Information ..................................................................................................................... 5

Pole Chainsaw Assembly .............................................................................................................................. 6

Saw Chain Tension ....................................................................................................................................... 8

Saw Chain Tension Adjustment ............................................................................................................... 8

Operation .................................................................................................................................................................. 10

Cutting with the Cordless Pole Chainsaw .................................................................................................... 10

Maintenance ............................................................................................................................................................ 11

Cleaning the Saw Body ............................................................................................................................... 11

Guide Bar Maintenance ............................................................................................................................... 11

Sharpening the Saw Chain .......................................................................................................................... 12

Filing Cutter Depth Gauges ......................................................................................................................... 13

Replacing the Saw Chain ............................................................................................................................ 14

Storage ...................................................................................................................................................................... 15

Battery Disposal and Recycling ........................................................................................................................ 15

Technical Specifications ...................................................................................................................................... 16

Summary of Contents for PLTCLSBMRAMC2




















Search results

Summary of Contents for PLTCLSBMRAMC2

Reviews:

Related manuals for PLTCLSBMRAMC2

Brands by name

Popular brands

Baumr-AG PLTCLSBMRAMC2, User Manual

Search results

Summary of Contents for PLTCLSBMRAMC2

Reviews:

Related manuals for PLTCLSBMRAMC2

Brands by name

Popular brands