Baumer EAM MT Series Manual Download Page 4

Page: 4 / 28

Baumer_EAM580_360_CANopen_MA_EN_Rev0003.0000h_Index0004.docx

Baumer Electric AG

06.08.2018

4/28

Frauenfeld, Switzerland

1 Version overview

This document is subject to changes. In order to have the most current version please download on

www.baumer.com

Document

index

Date

Firmware

version

CANopen

Revision

Number

Obj. 1018

Author

Changes

0001

11.07.17

From V01-03

0003.0000h

blk

Initial version replaces all draft documents

0002

11.9.17

From V01-04

0003.0000h

bwm

- Scaling function expanded up to 16Bit ST

New „speed Filter time“ default value of 50ms (Object

4001h) range reduced from 4000 ms to 500 ms

Comment “Emergencies are not resent after NMT
reset” removed in chapter 5.1.1

0003

12.03.18

From V01-05

0003.0000h

zest

- New profile version identification

Comment “Emergencies are not resent after NMT

communication

reset” removed chapter 5.1.2

- New function electronic gear, chapter 4.4.5 (Obj. 2001h)

- Reworked chapter 8 and 9

- New function error injection, chapter 9.4

- Added chapter 4.5.2 Node Id for redundant Encoder

0004

29.03.18

From V01-05

0003.0000h

zest

- fixed wrong sub-indexes in chapter 9.4

- fixed data flow of magnetic field strength and magnetic

field sequence in Figure 6

- fixed wrong object number in table of chapter 7.4.1

- comment added electronic gear function for non-

redundant encoders

Summary of Contents for EAM MT Series





























Search results

Summary of Contents for EAM MT Series

Reviews:

Related manuals for EAM MT Series

Brands by name

Popular brands

Baumer EAM MT Series, Manual

Search results

Summary of Contents for EAM MT Series

Reviews:

Related manuals for EAM MT Series

Brands by name

Popular brands