Baumer EAM MT Series Manual Download Page 18 | Manualshive

Page: 18 / 28

background image

Baumer_EAM580_360_CANopen_MA_EN_Rev0003.0000h_Index0004.docx

Baumer Electric AG

06.08.2018

18/28

Frauenfeld, Switzerland

9.4

Error Injection

The error injection allows testing a system behavior in case of an encoder malfunction.

There are two objects that can be used for test purposes to simulate different encoder behaviors.

0x2116-1 Diagnostic Injection

An error injection code, written on this object simulates a diagnostic source according to chapter 9.5.and activates the

corresponding signaling. For error injection codes please refer to chapter 9.5.

0x2116-2 Position Offset Injection

The value written to this object is added to the encoder position value, for test purposes

«
...
16
17
18
19
20
...
»

Summary of Contents for EAM MT Series





























Reviews:

No comments

Related manuals for EAM MT Series

Brand: ABB Pages: 10

Brand: Bang & Olufsen Pages: 44

Brand: ICP DAS USA Pages: 85

Brand: ICP DAS USA Pages: 6

Brand: ICP DAS USA Pages: 107

Brand: ICP DAS USA Pages: 8

Brand: ICP DAS USA Pages: 12

Brand: Yamaha Pages: 30

PowerRouter PR50S

Brand: Nedap Pages: 64

Brand: Lenze Pages: 132

Brand: IDK Pages: 44

Brand: Naxa Pages: 36

Brand: Saftronics Pages: 113

Brand: CEntrance Pages: 14

Brand: EMS Pages: 18

Brand: M-system Pages: 3

Pocket Inverter 100

Brand: XPower Pages: 38

L.O.C.PRO LP7-4

Brand: PAC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands