background image

               

How to install or remove score 

          blades on a 714XLT 

 
(Continued from previous page) 
 

 
11. Slide the left pullout tire assembly directly under pullout tire on the top slitter shaft and tighten the 

setscrew to hold the pullout assembly in place. 

 
12. Replace  the 

left slitter shaft boxing

 and tighten the socket head bolt into the tie bar 

 
13. Replace 

slitter shaft assembly

 into the folder in reverse order it was removed. 

 
14. Replace feed table in reverse order removed. 
 
15. Turn the folder by hand to insure nothing is loose or rubbing and that everything is free. 
 
16. Set up folder and run sheet through by hand and move perforator into position desired and lock 

any setscrews you may have moved.  Turn another sheet through by hand, and if ok, plug in 
folder. 

 
17. Turn on and run a sheet through and check fold and location.   If ok run job. 
 

 
Continued on next page… 
 

Baumfolder Corporation    P.O. Box 728  1660      Campbell Rd,  Sidney, Ohio USA  45365     Copyright © 2002 
 Phone  1-800-543-6107   or  1-937-492-1281    Fax   1-937-492-7280       email: [email protected]

 

Summary of Contents for 714XLT














Reviews: