background image

               

Set up instructions for the 714XLT 

Baumfolder Corporation    P.O. Box 728  1660      Campbell Rd,  Sidney, Ohio USA  45365     Copyright © 2002 
 Phone  1-800-543-6107   or  1-937-492-1281    Fax   1-937-492-7280       email: [email protected]

 

 
Time to set up a job….. 

 
 
 

We are now ready to set up a job on the folder.  Ask your customer for a sample of the job he/she wants 
to run.  This will give you, the sheet size and type fold.  Let’s take for example an 8 ½ “ x 11” letter fold. 
The example shown is with the header folded in. 

 
 

1.  Loosen the locking screws on the feeder side guides. Turn the 

knobs on the back of the Side guides and set them on 8 ½ on the 
scale, actual 4 ½ “ from the center of the feeder.  Lay a sheet of 
paper you are running between the guides and it should slide down 
but not have very much movement side to side.  This is the key to 
good folding.  IF THE GUIDES ARE TOO TIGHT, IT WILL NOT 
FEED WELL.  If the guides are to loose, the fold will vary.  If a fold 
is always crooked, usually the cause is that the side guides are not 
square with the number one fold roller.  See appendix A for 
correction. Set the magnetized angle stop at the back of the sheet.  

 
2.  Insert two thickness of paper between the caliper tab and the 

sucker wheel. Turn the gap knob counter-clockwise to tighten or 
clockwise to loosen. Set the gap knob until there is a slight drag on the 
paper. Remove the paper and the correct gap is now set. When you load 
the feeder, the printing will be up. 

 
3.  The front blow will normally be set properly. If not, it should be set so it 

separates the bottom sheets.  The adjustment knob on the side of the 
feeder is to set the blow in the side guide and front blow.  Turn the knob to 
the right to obtain more blow on the right side and front of the feed table.  
Turn the knob to the left to obtain more blow on the left and reduce the 
front blow.  

 
4.  Look on the folding chart on the stacker tray and locate 8 ½ x 11, fifth column over and letter fold 

second line down. It shows the first fold plate is set on E, and the 
second fold plate is set on E. On the fold plates approximately 3 ½ “ 
from the nose of the fold plate are the letter E (on both sides,) in a red 
circle with a line from it. Depress the course adjustment knobs and 

move the paper stop until it is on or close to the red line out 
from the letter E.  At the end away from the rolls of the 
adjustment rods are micro adjustment knobs. You can move 
these knobs to align the paper stops on the red line. Both fold 
plates should have the open end toward the fold rollers and 
the deflector away from the fold rollers. Both fold plate stops 
are adjusted the same way. 

 
 (continued) 

 

Summary of Contents for 714XLT














Reviews: