background image

Page 8

For technical questions, please call 1-888-866-5797.

Item 58215 

        

SA

FE

TY

OP
ERA

TI

O

N

MAINT

ENANC

E

SE

TUP

Extension Cords

Note:

  Extensions cords must not be used with this tool.

Service Precautions

Ground Fault Circuit Interrupter Protection

This tool is provided with a ground-fault circuit-interrupter (GFCI) built into the plug of the power-supply 

cord. This device provides additional protection from the risk of electric shock. Should replacement of the 

plug or cord become necessary, use only identical replacement parts that include GFCI protection.

Servicing a Double-Insulated Appliance

In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding 

means is provided on a double-insulated product, nor should a means for grounding be added to the 

product. Servicing a double-insulated product requires extreme care and knowledge of the system, 

and should be done only by qualified service personnel. Replacement parts for a double-insulated 

product must be identical to the parts they replace. A double-insulated product is marked with the words 

“DOUBLE INSULATION” or “DOUBLE INSULATED.” The symbol 

 may also be marked on the product.  

Summary of Contents for 21713E-B





















Reviews: