background image

CONCRETE SAW INSTRUCTION MANUAL

 

 

 

 BARTELL MORRISON INC.   

 BARTELL MORRISON (USA) LLC

375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX 905-364-4201

12 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY, USA, 07735, 732-566-5400 FAX 732-5444

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Created: 12/08

Revised: 12/10

CONCRETE SAW

ASSEMBLY AND OPERATING MANUAL

Save This Manual

 

You will need this manual for the safety warnings and precautions, assembly, operating, 

inspection, maintenance and cleaning procedures, parts list and assembly diagram.  Keep your 

invoice with this manual.  Write the invoice number on the inside of the front cover.  Write the 

product’s serial number in the back of the manual near the assembly diagram, or write month and 

year of purchase if product has no number.  Keep this manual and invoice in a safe and dry place 

for future reference.

GENERAL SAFETY RULES

Keep your work area clean and well lit

1. 

.  Cluttered and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of 

2. 

flammable liquids, gases, or dust.  

Power tools create sparks which may ignite the 

dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool.  

3. 

Distractions can cause you to lose control.  Protect others in the work area from debris 

such as chips and sparks.  Provide barriers or shields as needed.  Children should never 

be allowed in the work area.

PERSONAL SAFETY

Stay alert.  Watch what you are doing, and use common sense when operating a 

1. 

power tool.  Do not use a power tool while tired or under the influence of drugs, 

alcohol, or medication.  

A moment of distraction while operating power tools may result 

in serious personal injury.

Dress properly.  Do not wear loose clothing or jewelry.  Contain long hair.  Keep 

2. 

Summary of Contents for FS350














Reviews: