background image

CONCRETE SAW INSTRUCTION MANUAL

 

 

 

 BARTELL MORRISON INC.   

 BARTELL MORRISON (USA) LLC

375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX 905-364-4201

12 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY, USA, 07735, 732-566-5400 FAX 732-5444

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Created: 12/08

Revised: 12/10

PARTS LIST

ITEM

PART # Descrition

QTY ITEM

PART # Descrition

QTY

1

30451 Chassis Assy.

1

26

30426 Swivel Hose Fitting

1

2

30402 Rear Wheel

2

27

30427 Hose Washer

2

3

30403 Rear Axle Bearing

2

28

30428 Service Lever

1

4

30404 Splash Guard

2

29

30429 Water Hose

1

5

30405 Pivot Frame Assy.

1

30

*

Gas Engine

1

6

30406 Front Wheel

2

31

30431 Black Belt Guard

1

7

30407 Set Screw Collar

2

32

30432 Front Belt Guard

1

8

30408 Blade Shaft

1

33

30433 Shaft Cover Assy.

1

9

30409 Blade Shaft Bearing

2

34

30434 Engine Pulley

1

10

30410 Inner Blade Collar

1

35

30435 V-Belt

2

11

30411 Outer Blade Collar

1

36

30436 Blade Guard Assy.

1

12

30412 Pulley

1

37

30437 Blade Wrench

1

13

30413 Handle  

2

38

30438 Water Manifold

1

14

30414 Screw Jack Holder

1

39

30439 Brass Water Pipe

2

15

30415 Screw Jack  

1

40

30440 Guard Lock

3

16

30416 Bearing Bracket Adjuster

1

41

30441 Grease Fitting

6

17

30417 Hand Wheel Assy.

1

42

30442 Hose Clamp

2

18

30418 Screw Jack Nut

1

43

30443 Hose Nipple

1

19

30419 Handle Wheel Knob

1

44

30444 Blade Splash Guard

1

20

30420 Handwheel Lock Pin

1

45

30445 Screw Jack Nut

1

21

30421 Saw Guide

2

46

30446 Hex Bolt

1

22

30422 Guide Wheel

1

47

30447 Hex Bolt

1

23

30423 Washer Spacer

2

48

30448 Hex Bolt

1

24

30424 Pointer

1

49

30449 Saw Depth Stop

1

25

30425 Nut

1

50

30450 Outer Circlip

2

* Engine part number is dependent on the specific Gas Engine.  Please contact factory.

NOTE:

Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Summary of Contents for FS350














Reviews: