background image

CONCRETE SAW 

OI 

– B19041 

OWNER’S MANUAL 

 

 

Operating Safety continued:  

 
The engine section of this saw requires an adequate free flow of cooling air. Never operate the 
saw in any enclosed or narrow area where free flow of the air is restricted. If the air flow is 
restricted it will cause serious damage to the saw or engine and may cause injury.  
 
Remember the saw’s engine gives off deadly carbon monoxide gas. Us only in well ventilated 
area. 
 
Always refuel in a well-ventilated area, away from sparks and open flames.  
 
Always use extreme caution when working with flammable liquids. When refueling, stop the 
engine and allow it to cool. Do not smoke around or near the machine. Fire or explosion could 
result from fuel vapors, or if fuel is spilled on a hot engine.  
 
Topping-off to the fuel filler port is dangerous, as it tends to spill. Never use fuel as a cleaning 
agent.  
 
Always be sure to operator is familiar with proper safety precautions and operating techniques 
before using the saw. Know how to stop the saw in case of emergency. 
 
Keep both hands on the handle while using the saw. Stop the engine when leaving the saw 
unattended.  
 
Block the wheels when leaving or when using on a slope.  
 
Maintain this equipment in a safe operating condition at all times. Ensure all fasteners are tight 
 
Never run engine without air filter. Severe engine damage may occur. Always service air 
cleaner frequently to prevent carburetor malfunction.  
 
Always store equipment properly when it is not being used. Equipment should be stored in a 
clean, dry location out of the reach of children.  
 
Never operate this saw in areas that contain combustible material or fumes. Fire and/or 
explosions may result from errant sparks from the equipment.  

 

Summary of Contents for BSS18H39W

















Reviews: