background image

CONCRETE SAW 

OI 

– B19041 

OWNER’S MANUAL 

 

 

WARRANTY INFORMATION 

– BSS18H39W 

 

All products sold by Bartell Morrison Inc. and Bartell Morrison (USA) LLC (the “Company”) are 
warranted against defects in materials and/or workmanship for a period of 12 months; excluding 
the normal wear on wearing components and components covered by a separate original 
manufacturer’s warranty. The warranty is to the original end user purchaser provided that 
certain conditions have been met. 
Conditions: 
 

1.  The equipment serial number has been registered with the Company or its approved 

dealers, distributors, and representatives or agents. 

2.  The equipment has been operated in an appropriate manner by qualified individuals. 
3.  The equipment has been properly maintained as per the instructions included in the 

Owner’s Manual. 

4.  All claims for warranty must be filed on proper forms and include the serial number of the 

equipment along with proof of purchase. 

 
Any evidence of failure to meet these conditions may result in a denial of the warranty claim. 

 

Consideration of warranty claims will be at the sole discretion of the Company, or its authorized 
dealers, distributors, representatives or agents. 

 

The Company may, at its discretion, request that the equipment to be considered for warranty 
be returned at the owner’s expense to an authorized repair facility for inspection. 

 

Under this warranty we may, at our discretion, replace the defective portion of the equipment 
and a reasonable (as determined by the Company) amount of labour to conduct the repair or 
replacement.  
 
Under no circumstances shall the Company be liable for any additional or exceptional costs 
beyond the cost to repair or replace the defective portion of the equipment. The Company shall 
not be held accountable for; costs associated with travel to inspect or repair defective 
equipment, cost for transporting equipment at any facility other than one authorized by the 
Company or ancillary damage caused by or as a result of defective equipment. 

 

Under no circumstances shall equipment be returned to the Company or its authorized dealers, 
distributors, representatives, or agents without the approval of the Company as evidence by a 
Returned Goods Number. To obtain a Returned Goods Number contact the factory or your au-
thorized dealer, distributor, representative or agent. 

 

This warranty is for the sole benefit of the original end user purchaser and is not transferrable to 
any other company or person.  
 
 

 

Summary of Contents for BSS18H39W

















Reviews: