background image

CONCRETE SAW 

OI 

– B19041 

OWNER’S MANUAL 

 

 

 

 

Bartell Morrison Inc. 

170 Traders Blvd E 

Mississauga, Ontario, Canada 

L4Z 1W7 

Tel: (647) 953-4100 

Fax: (647) 953-4101 

Bartell Morrison USA LLC 

200 Commerce Drive, Unit A 

Freehold, NJ, USA 

07728 

Tel: (848) 225-8100 

Fax: (848) 225-8101 

SPE International Ltd 

Honeyholes Lane 

Dunholme, Lincoln, England 

LN2 3SU 

Tel: 01673 860709 

Fax: 01673 861119 

 

Innovatech 

832 80

th

 Street SW 

Everett, Washington, USA 

98203 

Tel: (425) 405-9100 

Fax: (425) 405-9101 

 

 

ORIGINAL LANGUAGE OPERATING MANUAL FOR 

BARTELL STREET SAW BSS1813, BSS1813W 

 

© 2019 Bartell Morrison Inc. 

No part of this work may be reproduced or transmitted in any form or by any means, electronic 

or mechanical, including photocopying and recording, or by any information storage or retrieval 

system without the prior written permission of Bartell Morrison Inc. unless such copying is 

permitted by federal copyright laws.  

 

Address inquiries or reference permissions care of: 

Bartell Morrison Inc., 170 Traders Blvd. E, Mississauga, Ontario, Canada, L4Z 1W7

 

 
 

REV.

 

DATE

 

DESCRIPTION

 

APPROVED BY: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for BSS18H39W

















Reviews: