background image

Installation Instruction 

(Translation) 

RFID UHF Add-On Module 

Type B7-A2Z0-0032 

 

Technical data subject to change. 

08/2016 

EN   1/11

 

 

 

Basic Information

 

Read carefully before putting the devices into operation.

 

The Installation Instruction is a fixed part of the product. It must be kept in the direct 

vicinity of the device and the installation, operating and service staff must have access 

to it at all times. 

More detailed instructions of the use can be found at 

www.bartec.de

 as well as t

he current versions 

of the datasheets, user manual, certificates and EU declaration conformity or may be requested 

directly from BARTEC GmbH.

 

Knowledge of the safety and warning information and the strict compliance with it is essential for 

safety installation and use. Injuries and material damage can be avoided by circumspect handling 

and systematically following the instructions.  
The BARTEC company reserves the right to carry out technical changes at any time.  

Maintenance and Repairs 

The pertinent erection and operating provisions for electrical systems 

must be observed! Repairs to explosion-protected devices may only be performed  by authorised 

personnel with original spare parts and according to the state of the art. The applicable provisions 

must be observed in this respect. 

Inspections 

According to EN/IEC 60079-17 and EN/IEC 60079-19, the operator of electrical 

systems in potentially explosive atmospheres is obliged to have these inspected by an electrician to 

ensure correct condition. 

Warranty 

If non-specified components are used, the explosion protection will no longer be 

guaranteed. In the case of externally procured parts, it  is not guaranteed that these have been 

designed and manufactured in accordance with their load and requisite safety. 

Disposal 

As professional electrical devices, our devices are intended exclusively for commercial 

use, so-called B2B devices, in accordance  with the WEEE Directive. Observe the national waste 

disposal regulations when disposing of the devices. All products purchased from us can be returned 

to us by our customers for disposal. The sender shall bear the costs of postage and packaging. 

 

Summary of Contents for B7-A2Z0-0032

















Reviews: