Baroness LM315GC Owner'S Operating Manual Download Page 25

Page: 25 / 86

Inspection Before Use ...........................Page 4-2

Tightening torques .............................. Page 4-10

Standard tightening torques ................ Page 4-10
Principal tightening torques ................. Page 4-12

Adjustment Before Operating .............Page 4-14

Adjustment of Seat .............................. Page 4-14
Adjustment of Steering Wheel ............. Page 4-14
Adjustment of Blade Engagement ....... Page 4-15
Adjustment of Cutting Height ...............Page 4-16
Adjustment of Groomer ........................Page 4-18
Cutting Height and Blade Thickness
of Bed Knife (Bottom Blade) ................ Page 4-20
Adjustment of Cutter Adjustment
Spring .................................................. Page 4-21

Procedure to Start / Stop Engine ....... Page 4-21

Start / Stop of Engine .......................... Page 4-21
Safety Mechanisms ............................. Page 4-23
Warning Mechanisms .......................... Page 4-23

Operation of Each Section ..................Page 4-23

Precautions for Operating the
Machine ............................................... Page 4-23
Cautions for when You Leave the
Machine ............................................... Page 4-23
Description about Operation Decals ....Page 4-23
Light Switch ......................................... Page 4-27
Throttle Lever .......................................Page 4-28

Instruments .......................................... Page 4-34

Instruments on the Operation Panel ....Page 4-34
Hour meter ...........................................Page 4-35
Fuel Gauge ..........................................Page 4-35

Travel of Machine ................................ Page 4-35

Moving the Machine ............................ Page 4-35
Towing the Machine ............................ Page 4-35

Cutting Work ........................................ Page 4-36

Cutting Work ........................................Page 4-36
Reel Refreshing Operation .................. Page 4-37
Removing Grass Catcher .................... Page 4-38

Transporting .........................................Page 4-38

Transporting Procedure .......................Page 4-38

Handling Instructions

LM315GC

Handling Instructions

Page 4-1

Summary of Contents for LM315GC























































































Search results

Summary of Contents for LM315GC

Reviews:

Baroness LM315GC, Owner'S Operating Manual, Page: 25 / 86

Search results

Summary of Contents for LM315GC

Reviews: