manualshive.com logo in svg

Baroness LM315GC, Owner'S Operating Manual, Page: 51 / 86

Share
Download
Baroness LM315GC Owner'S Operating Manual Download Page 51

8

LM315GC1418Z0
Decal, reel rotation changeover
It illustrates the rotation changeover of the reel cutter
(cutting cylinder) for High speed, Low speed and
back lapping.
1.High
2.Low
3.Back lapping

1

2

3

6n6oux-035

9

K4203001550
Decal, mower unit reel rotation changeover
It illustrates the rotation changeover of the reel cutter
(attached to the mower unit) for Normal rotation,
Neutral and Reverse rotation.
1.Normal rotation
2.Neutral
3.Reverse rotation

1

2

3

6n6oux-036

Light Switch

Note:
Depending on the specifications, this function
may not be available.
The light switch is located in the operation
panel.
Flip the switch up to turn the light on, and down
to turn the light off.

( - #30420)

1

B

A

bnec97-017

Light Switch_001

(#30421 - )

MOW

TRAVEL

3

WD

2

WD

1

B

A

bnec97-016

Light Switch_002

1

Light switch

A

ON

B

OFF

Handling Instructions

LM315GC

Handling Instructions

Page 4-27

Operation of Each Section

Summary of Contents for LM315GC























































































Reviews:

No comments