manualshive.com logo in svg

Baroness LM315GC, Owner'S Operating Manual, Page: 55 / 86

Share
Download
Baroness LM315GC Owner'S Operating Manual Download Page 55

Reel Rotation Switch

Warning

Set the reel rotation switch to the "TRAVEL"
(reel stop) position except during mowing or
backlapping and using reel excess discharge
system.

Caution

In case of 2WD/3WD model, travel in 2WD
mode since it is dangerous to travel on steep
downward slopes, wet road surface or
downward slopes of wet lawn in 3WD mode.
Rear tire going into a skid may cause loss of
traveling control.

Important

In case of 2WD/3WD model, whenever the
reel rotation switch is set to the "MOW" (reel
rotation) position, the drive mode is put into
3WD regardless of the position of the
2WD/3WD selector switch.

( - #30420)
The reel rotation switch is located on the
right of the foot area in front of the driver's
seat. Setting the switch to the "MOW" (reel
rotation) position rotates the reel, and to the
"TRAVEL" (reel stop) position stops the reel.

1

B

A

mh4pyw-006

Reel Rotation Switch_001

1

Reel rotation switch

A

Rotate

B

Stop

(#30421 - )
The reel rotation switch is located in the
operation panel. Setting the switch to the
"MOW" (reel rotation) position rotates the
reel, and to the "TRAVEL" (reel stop)
position stops the reel.

MOW

TRAVEL

3

WD

2

WD

1

B

A

v2e27i-030

Reel Rotation Switch_002

1

Reel rotation switch

A

Rotate

B

Stop

When the reel rotation switch is set to the
"MOW" (reel rotation) position, the reel cutters
(cutting cylinders) will rotate or stop in sync
with the up and down motion of the mower
units. When the mower units are lowered, the
reel cutters (cutting cylinders) rotate, and when
the mower units are raised, they stop.

When the mower units are lowered, the
sensor activates the electromagnetic clutch,
and the reel cutters (cutting cylinders) start
rotating by means of the flexible wire.
When the mower units are raised, even if the
reel rotation switch is set to the "MOW" (reel
rotation) position, the sensor does not
activate the electromagnetic clutch, and the
reel cutters (cutting cylinders) do not rotate.

1.

2.

Handling Instructions

LM315GC

Handling Instructions

Page 4-31

Operation of Each Section

Summary of Contents for LM315GC























































































Reviews:

No comments