background image

Manual 2100-701
Page 

6 of 16

BASIC FIELD INSTALLATION

1.  Unpack the ventilator assembly which includes the 

integral ventilator with attached electrical harness 
and miscellaneous hardware.

2.  Disconnect unit power.

3.  Remove the existing exterior blower access, filter 

access and vent option panels on the wall mount 
unit (see Figure 1). Save the blower access and 
filter access panels and discard the vent option 
panel.

Model

For Use with the 

Following Units

Electrical

ERV-FA2

W18AB-A

W24AB-A, -B

W18HB-A

W24HB-A, -B

230/208V

1 or 3 phase

ERV-FC2

W24AB-C

W24HB-C

460V

3 phase

ERV-FA3

W30AB-A, -B
W36AB-A, -B

W30HB-A, -B
W36HB-A, -B

230/208V

1 or 3 phase

ERV-FC3

W30AB-C
W36AB-C

W30HB-C
W36HB-C

460ERV-F

3 phase

Be sure the correct model and voltage 

energy recovery ventilator is used with 

the correct air conditioner or heat pump to 

ensure correct voltage compatibility.

!

CAUTION

!

WARNING

Open and lock unit disconnect switch 

before installing this accessory to prevent 

injury or death due to electrical shock or 

contact with moving parts. Turn thermostat 

to OFF.

FIGURE 1

Remove Access Panels

BLOWER ACCESS 
PANEL

FILTER ACCESS PANEL

VENT OPTION PANEL

TABLE 1

Model Reference

Summary of Contents for ERV-FA2

















Reviews: