Manual 2100-684B
Page
8 of 10
If COMP LOCKOUT was chosen during the heat
strip configuration process, an optional outdoor
air temperature sensor will have to be installed/
configured to specifically set the temperature at which
the compressor will no longer be allowed to operate.
Refer to the latest version of
CompleteStat Controller
Advanced Programming & Features 2100-685
to
configure the outdoor air temperature sensor.
To install Bard 8403-061 Outdoor Air Temperature
Sensor, attach the leads to terminals “OAT” and
“GND”. To set the compressor outdoor air temperature
limits from the home screen:
1. Press
RIGHT button to access Main Menu screen.
2. Press
DOWN button to scroll to TECHNICIAN.
Press ENTER button.
3. In the TECHNICIAN menu screen, press UP or DOWN
button to scroll to LIMITS. Press ENTER button.
4. Press DOWN button to scroll to COMP OAT CLG
LOW. Press ENTER button.
5. Press UP or DOWN button to select outdoor air
temperature for compressor lockout (factory default
0ºF). Press ENTER to save choice.
6. Press LEFT button to return to TECHNICIAN menu.
Ventilation, Fan and Humidity Setup
1. In the TECHNICIAN menu screen, press ENTER
button to enter the APPLICATION menu.
2. Press DOWN button to scroll to ADDITIONAL
SETUP. Press ENTER button.
3. Press DOWN button to scroll to VENTILATION.
Press ENTER button.
4. Press UP or DOWN button to choose from the
available economizer options:
•
NONE = No economizer, or standard vent
package (ERV/CRV/MFAD). This is the factory
default.
•
EN/DIS = Economizer in system
5. Press ENTER button to select/save appropriate
economizer option.
6. Press LEFT button to go back to ADDITIONAL
SETUP.
7. The indoor blower can be set for ON or AUTO
in either occupied or unoccupied conditions.
To
access or change blower settings, press DOWN
button to scroll to FAN. Press ENTER button to
enter FAN SETUP (see Figure 9).
8. Press DOWN button to scroll through selections;
adjust as necessary.
•
Speeds: Constant speed (nonadjustable)
•
Off Delay: “0” = System fan will run for
specified time after call ends; 0-600 seconds
in 30-second increments.
FAN SETUP
SPEEDS:
CONSTANT SPEED
OFF DELAY (SECS): 0
UNOCC: AUTO
OCC: AUTO
FIGURE 9
Fan Setup (Heat Pump)
•
Unocc: “ON” = System fan will run continuously
during all operational modes; “AUTO” = System
fan will operate during call for cooling or
heating, but will cycle off when no compressor
or no heating is needed (factory default).
•
Occ: “ON” = System fan will run continuously
during all operational modes; “AUTO” =
System fan will operate during call for
cooling or heating, but will cycle off when no
compressor or no heating is needed (factory
default).
9. Press ENTER button to save changes to FAN
SETUP selections.
10. Press LEFT button to go back to ADDITIONAL
SETUP.
11. Press DOWN button to scroll to HUMIDITY. Press
ENTER button to enter HUMIDITY SETUP.
12. Press ENTER button again to choose
DEHUMIDIFICATION (see Figure 10).
13. Press ENTER button again to highlight current
dehum choice (default is ENABLE).
14. Press UP or DOWN button to toggle ENABLE/
DISABLE. Press ENTER button to select/save
choice.
15. Press DOWN button to scroll through additional
DEHUMIDIFICATION screen choices:
•
ALLOW HTG DEHUM = Allows
dehumidification in heating as well as cooling:
YES/NO (default is YES).
•
DEHUM SETPT = Relative Humidity (RH)
setpoint: 45% RH to 80% RH, 1% increments
(default is 60%RH).
•
DEHUM SPAN = Amount of RH% removal
allowed past setpoint: 5% to 10%, 1%
increments (default is 5%RH).
16. Press ENTER button to save changes.
