background image

K5902157-01

Nio 3MP LED Display

24

4.7 Hibernate

About hibernate

When hibernate is enabled, not only the backlight will be switched off, but also other functionalities will be
disabled to further reduce power consumption to a minimum. This happens after a specific period of time
which can be manually adjusted.

Hibernate can only be enabled on your display when the DPMS mode is enabled first. Therefore,
please refer to

DPMS mode

page 23 to do this.

Please connect your keyboard or mouse to your PC rather than to the display's USB ports when
hibernate is enabled.

To enable/disable hibernation on your display:

1.

Bring up the OSD main menu.

2.

Navigate to the

Configuration > Power Management

menu.

3.

Enter the

Hibernate

submenu.

4.

Select

Enabled/Disabled

as desired and confirm.

To specify the hibernate time-out:

1.

Bring up the OSD main menu.

2.

Navigate to the

Configuration > Power Management

menu.

3.

Enter the

Hibernate Timeout

submenu.

4.

Set the time-out value as desired and confirm.

4.8 Luminance target

About the luminance target

The luminance target of your Nio 3MP LED Display is adjustable over a predefined range. When you change
the luminance target, the display will adjust its backlight to reach the target.

To set the luminance target:

1.

Bring up the OSD main menu.

2.

Navigate to the

Configuration > Calibration

menu.

3.

Enter the

Luminance Target

submenu.

4.

Set a luminance target value as desired and confirm.

The default, factory DICOM calibrated luminance value is available in the technical specifications
table. The guaranteed backlight lifetime is valid for this setting.

4.9 Viewing modes

About viewing modes

The Nio 3MP LED Display can be used in two viewing modes:

Diagnostic:

This mode provides the full calibrated luminance and is intended for using the display for

diagnostic purposes.

Text:

In this mode, the luminance is reduced to approximately half of the luminance. This is intended for

using the display with office applications such as word processing.
Please note that text mode is not persistent, once powered off, the unit will restart in diagnostic mode.

Advanced operation

Summary of Contents for Nio 3MP LED





















































Reviews: