R5905752 /16
DP2K C
28
8.
Installation of the HDDs.
In case the HDDs of the ICMP are delivered separated from the projector
remove the protection tape from the HDD input slots and install all three HDDs as described in the
procedure
Installing a HDD into the ICMP-X
, page 90. Make sure that all HDDs in the ICMP-X HDD set
have the same storage capacity. See label on top of the HDD to know the storage capacity.
9.
Alignment of the projected image on the screen
. The projector can now be switched on to project its
first image (test pattern) on the screen. Then the image can be aligned with the screen size of the
application. Follow the next steps to achieve that:
1. Place the
ON/OFF
switch of the projector in the
”
I
”
position. As a result the projector starts to initialize.
The status lights of the projector lights up GREEN once the projector is initialized.
2. Press the
STANDBY
button on the local keypad to activate the lamp.
3. Press the
DOWSER
button on the local keypad to open the dowser of the projector. The dowser is
open if the color of the DOWSER button is GREEN.
4. Press the
TEST PATTERN
button on the local keypad to project one of the internal test patterns of the
projector on the screen.
5. Use the lens
ZOOM
,
SHIFT
and
FOCUS
buttons on the local keypad the match the projected image
with the screen. Tilt the projector in case you can not SHIFT the image completely upon the screen.
See
”
, page 62.
10.
Resetting the lamp parameters
. The
“
LAMP INFO
”
parameters which are stored on the controller board
of the projector MUST be updated after each installation of an xenon lamp inside the lamp house.
Neglecting this update will result in poor performance and short life time of the xenon lamp. See chapter
”
, page 53.
11.
Realignment of the xenon lamp in its reflector
. For optimal performance of the xenon lamp it is required
to realign the lamp after installation in the lamp house. See
“
Realignment of the lamp in its reflector
”
, page
54 for more information.
12.
Adjusting the light path
. Normally the lens holder and the convergence of the projector is perfectly
adjusted at the factory. Nevertheless, some applications require a readjustment of the lens holder,
convergence or both. See procedure
”
, page 64, to adjust the Scheimpflug and
see chapter
“
, page 143 to adjust the convergence of the light path.
13.
Registration of the projector
. The DP2K-xxC is DCI compliant and should be registered.
14.
Projection of a digital cinema movie
.
In case the projector is equipped with an ICMP-X, download the ICMP-X device certificate, request KDM
and DCP from your content supplier, ingest KDM and DCP, and play out the movie. for detailed
instructions see chapter
”
, page 83, and user guide of the Communicator and/or (Web)
Commander.
In case the projector is equipped with a HD-SDI input module apply a single or dual channel SMPTE (HD-
SDI) source to the input ports of the HD-SDI input module and start up the projector. See chapter
“
”
, page 74 . Use the Communicator (Touch Panel) to configure the applied source.
See the user guide of the Communicator (Touch Panel) for more detailed information. (not for Taiwan
market)
In case the projector is equipped with an Integrated Media Block (IMB) or Integrated Media Server (IMS)
see user guide of the IMB or IMS for detailed instructions. (Not for Taiwan market)
Summary of Contents for DP2K C
