![background image](http://html1.mh-extra.com/html/barco/coronis-5mp-mammo/coronis-5mp-mammo_system-manual_3886855032.webp)
System manual Coronis 5MP
33
Settings
Settings
Settings
Settings
Settings
To change the settings:
1 Turn the control wheel to select the setting you wish to change.
2 Click the control wheel to change the setting.
The Settings menu cont
The Settings menu cont
The Settings menu cont
The Settings menu cont
The Settings menu contains the following items:
ains the following items:
ains the following items:
ains the following items:
ains the following items:
DPMS ................... Allows to switch on/off the automatic power saving
system (DPMS)
Power LED ........... This setting allows you to switch off the power
LED. Note: The LED’s orange DPMS state is not
influenced by this setting. So, when the display
goes into power-saving mode, the LED will turn
orange, even if it was switched off by this setting.
User controls ........ This function allows you to disable the control
wheel functions so that the on-screen display
cannot be used after quitting the OSD menus.
T
T
T
T
To enable the control wheel functions again
o enable the control wheel functions again
o enable the control wheel functions again
o enable the control wheel functions again
o enable the control wheel functions again:
a) Do not use the wheel for at least 3 seconds
b) Turn the control wheel 1 click clockwise
c) Click the control wheel 2 times
d) Turn the control wheel 1 click counterclockwise
e) Select the Settings menu and switch Local
controls on again.
Actions b, c, d have to be performed in a
Actions b, c, d have to be performed in a
Actions b, c, d have to be performed in a
Actions b, c, d have to be performed in a
Actions b, c, d have to be performed in a
sequence that t
sequence that t
sequence that t
sequence that t
sequence that takes no longer than 3 seconds.
akes no longer than 3 seconds.
akes no longer than 3 seconds.
akes no longer than 3 seconds.
akes no longer than 3 seconds.
Display installation
Getting information
Getting information
Getting information
Getting information
Getting information
The Information menu allows you to get a lot of information about the
display and the connected signals.
Proceed as follows:
1 In the main menu, turn the control wheel to select Information.
2 Click the control wheel to enter the information menu.
The Information menu cont
The Information menu cont
The Information menu cont
The Information menu cont
The Information menu contains the following items:
ains the following items:
ains the following items:
ains the following items:
ains the following items:
Product: ................... The display type
Serial No: ................ Indicates the display serial number
SW version: ............ Displays the current internal software version
Display Lifetime: ..... Indicates the total time the display has been
operating, including the time in stand-by
Backlight Lifetime: ... Indicates the total time the display has been
operating, excluding the time in stand-by
Summary of Contents for Coronis 5MP Mammo
