![background image](http://html1.mh-extra.com/html/barco/coronis-5mp-mammo/coronis-5mp-mammo_system-manual_3886855046.webp)
System manual Coronis 5MP
47
Inst
Inst
Inst
Inst
Installing the BarcoMed 5MP2F W
alling the BarcoMed 5MP2F W
alling the BarcoMed 5MP2F W
alling the BarcoMed 5MP2F W
alling the BarcoMed 5MP2F Windows NT
indows NT
indows NT
indows NT
indows NT 4.0
4.0
4.0
4.0
4.0
Sof
Sof
Sof
Sof
Software
tware
tware
tware
tware
SPECIAL
SPECIAL
SPECIAL
SPECIAL
SPECIAL NOTE:
NOTE:
NOTE:
NOTE:
NOTE: Prior to installing the BarcoMed drivers and related
software you MUST install the BarcoMed Display Controller(s),
connect the CORONIS display panel(s) to the card(s), and turn the
CORONIS display panel(s) on. Refer to the Hardware Installation
section of this manual for instructions on installing the BarcoMed
Display Controller(s) and connecting them to the CORONIS display
panel(s).
The following software installation instructions presume that Windows
NT is already installed on your system. If you need to install or
reinstall Windows NT on your system you must first remove the
BarcoMed Display Controller(s) and use a 3
rd
party VGA card and
VGA monitor during the Windows NT installation process.
Using the BarcoMed Product Installation Wizard
Using the BarcoMed Product Installation Wizard
Using the BarcoMed Product Installation Wizard
Using the BarcoMed Product Installation Wizard
Using the BarcoMed Product Installation Wizard
To install your BarcoMed 5MP2F Windows Display Controller Driver,
BARCO DPMS Screen Saver and CORONIS Rotation Service for the
first time follow the steps below. If you are reinstalling the drivers or
installing a new driver release over an existing driver release, skip
step 1 below:
1. Install the BarcoMed Display Controller(s) into your machine.
Please refer to the Hardware Installation section of this manual for
more information.
2. Boot the machine, log in using an account with administrator
privileges and follow these steps.
3. Insert your BarcoMed Software CD into your computer’s CD drive.
The “BarcoMed Software Product Installation Wizard” should start
automatically. If it doesn’t start within 3 minutes, browse the
contents of your BarcoMed Software CD and double click on the
file, “Setup.exe”
“Setup.exe”
“Setup.exe”
“Setup.exe”
“Setup.exe” to start the wizard.
The BarcoMed Product Installation Wizard will start by inspecting
your system to make certain that all of the necessary Windows
components are up to date. If it determines that the Microsoft
Installer is current, the BarcoMed Product Installation Wizard will
start by displaying the screen shown in figure 7. If it determines
that the Microsoft Installer is either out of date or missing, it will
display the screen shown in figure 5. Click “OK”
“OK”
“OK”
“OK”
“OK” to continue, the
wizard will then install a newer version of the Microsoft Installer.
BarcoMed software driver installation
Summary of Contents for Coronis 5MP Mammo
