Barbeques Galore Grand Turbo B4019LP Operator'S Manual Download | Manualshive

Page: 1 / 34

background image

Manual # P80151157B - Date:2020/10/14

Failure to comply with these instructions could
result in a fire or explosion that could cause
serious bodily injury, death or  property damage.
Whether this grill was  assembled  by you  or
someone else, you must read this entire manual
before  using  your  grill  to  ensure  the  grill  is
properly assembled, installed and maintained.

Use your grill at least 3 feet away from any
wall or surface.

Use your grill at least

3 feet

away

from combustible objects that can melt or

catch fire such as vinyl or wood siding, fences
and overhangs or sources of ignition including
pilot lights on water heaters and live electrical
appliances.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.

Never

use your gas grill in a garage, porch,

shed, breezeway or any other enclosed area.

Never

obstruct the flow of ventilation air

around your gas grill housing.

Never

disconnect the gas regulator or any gas

fitting while your grill is lit. A lit grill can ignite
leaking gas and cause a fire or explosion which
could result in property damage, personal injury
or death.

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

Ÿ

WARNING

!

!

Ÿ

Grill Information Center:

Ÿ

Ÿ

NOTE TO ASSEMBLER / INSTALLER:

Leave this manual with the consumer.

NOTE TO CONSUMER:

Keep this manual for future reference.

RECORD YOUR SERIAL #

__________________
(see silver CSA label on main body of grill)

IMPORTANT:

Ÿ

FREE HELP

FROM THE GRILL EXPERTS

Barbeques Galore

is the expert on this

product and trained to help you with:

visit www.grandhall.com or call:

1-800-474-5587
Monday - Friday 8:30am-4:30pm PST

Assembly Questions
Grill Operation
Replacement of Damaged or Missing parts

Ÿ

Ÿ

Ÿ

Liquid Propane Gas (LPG) Grill

Models B4019LP

Natural Gas (NG ) Grill

Models B4019NG

Operator's Manual

1
2
3
...
»

Summary of Contents for Grand Turbo B4019LP



































Reviews:

No comments

Related manuals for Grand Turbo B4019LP

3241GRILL20SEB03

Brand: Kamado Pages: 8

Super Champ GR12

Brand: George Foreman Pages: 11

PIT BOSS NAVIGATOR

Brand: Navigator Pages: 62

FlavorStone InfusionGrill

Brand: Thane International Pages: 2

Brand: tepro Pages: 96

Brand: Backyard Pages: 26

Brand: Fiesta Pages: 12

Brand: George Foreman Pages: 11

Brand: Racine Railroad Products Pages: 21

Brand: Argos Pages: 12

Brand: Parkside Pages: 64

Brand: Atlas Copco Pages: 28

Brand: arilex Pages: 38

Brand: Jet Pages: 16

Brand: Honeywell Pages: 22

GO-ANYWHERE 1141056

Brand: Weber Pages: 96

Brand: HART Pages: 24

LANGFORD KG180047

Brand: NORDIC SEASON Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands