background image

N

Note:
• Make sure the thickness of any plastering is taken into account when the

brickwork is being build.

• Do not use masking tape on the appliance. Masking tape damages the

paint on the appliance.

• If you use other material than bricks, install the material in accordance with

the instructions of the supplier of the material

• If you use other material than bricks, refer to the instructions of the supplier

of the used material for information on the need to use a mantle iron.

1. Identify the positions where the ventilation air inlet grates and the ventilation air outlet

grates must be put. Refer to 

6.1.2

 for requirements on the size of the ventilation air

openings.

2. If applicable, identify the positions where the fitting boxes of the convection air inlets

and convection air outlets must be put. Refer to 

6.1.2

 for requirements on minimum

distances from ceiling and neighboring wall.

3. Identify the position where the dimmer for the convection ventilator must be put.
4. Build the brickwork around the appliance up to the upper frame around the glass.

a) Install the fitting boxes of the ventilation air inlets.
b) If applicable, install the fitting boxes of the convection air inlets.
c) If applicable, install the dimmer of the convection ventilator.

5. If applicable, install a mantle iron to support the brickwork above the appliance. Put

the mantle iron on both sides of the brickwork. Maintain a space of at least 3 mm

between the appliance and the mantle iron.

6. If applicable, install the flexible aluminum pipes of the convection set. Refer to 

6.3.5

.

7. Build the fireplace around the appliance.

a) Install the fitting boxes of the ventilation air outlets.
b) If applicable, install the fitting boxes of the convection air outlets

8. Install the frame around the appliance.

6.3.8

Final check on the appliance

Caution:
Wait 4 weeks after the installation before you use the appliance. The cement

used for the fireplace needs to harden and to avoid damage to the plaster

work.

1. Make sure the door closes and opens easy.
2. Make sure the control lever moves easy to left and right without undue noise.
3. Make sure all cast iron plates and the baffles are in the correct position.
4. When applicable: Start the convection ventilator and make sure the ventilator does

not make an unusual noise (grinding sound). A soft hum is not an unusual sound.

Contact your dealer if the final check shows a defect.

Installation

24

Falcon 80/56

Summary of Contents for Falcon 80/56









































Reviews: