background image

®

January 2022 (v1.5)

6

VARIO+ OPERATIONS MANUAL

GRINDING OPERATION

After setting up the grinder as outlined in the previous section, press a 
preset button 

(9)

. The screen will show the corresponding programmed 

grind time in seconds. Press START/STOP 

(7)

 to begin grinding. While 

grinding, the screen will count down the seconds to 0.0. When the 
screen reaches 0.0 seconds, the motor will stop, and the display will 
reset again to the programmed time.

ADJUSTING THE GRIND SETTING: 

The Vario+ has a micro adjustment lever knob 

(5)

 to the left of the display and a macro adjustment lever 

knob 

(6)

 to the right. The Micro adjustment arm is used to make smaller changes to the grind size, while the 

macro adjustment arm is used to make larger changes. Twelve micro adjustment clicks are equivalent to 
one macro adjustment click. The grind setting is adjusted by moving the micro and/or macro adjustment 

lever knobs up or down.  Moving a lever arm up will result in a finer grind, whereas moving a lever arm down 
will result in a coarser grind.  When making a finer grind adjustment with coffee in the hopper, the motor 

must be running.

At setting 2Q and settings finer, the burrs 

(15)

 will audibly contact each other. The grinder is calibrated for 

the burrs to touch at this point, and it will not damage the burrs to grind at their contact point or finer if 
there is coffee being ground

. However, running the grinder without coffee while the burrs are touching for 

extended periods of time will reduce the lifespan of the burrs.

CHOOSING A GRIND SETTING FOR A BREW METHOD:

The settings shown in the table below should be used as a general starting point. The actual grind size needed 

for a particular brew method will vary depending on many factors, such as: degree of roast (light vs. dark), 
freshness, environmental humidity, variety of bean, oil content, etc. Practice and personal preference will 
ultimately determine which setting is right for the desired taste, brewing style, and the particular beans used. 

Espresso

AeroPress

Hario V60

Automatic 

Drippers

Chemex

French  

Press

2Q

4M

6M

7M

9M

10M

Summary of Contents for Vario+














Reviews: