background image

®

January 2022 (v1.5)

5

VARIO+ OPERATIONS MANUAL

GRINDER SETUP

1.  Place the grinder on a level surface. 
2.  Hand wash the hopper 

(2)

, hopper lid 

(1)

 and grounds bin 

(13)

 with warm soapy water. Let air dry 

or dry with a clean cloth.

3.  To install the hopper: With the hopper upright and the shut-off knob 

(3)

 pointing toward the 

back left of the grinder, place the hopper on top of the grinder and find the point where it settles 
into place. Push down and rotate the hopper clockwise to center the shut-off knob and lock the 
hopper into place. The hopper must be locked into place to engage the microswitch so that the 
grinder can operate.

1

4.  The grinder will come with the PortaHolder 

(10)

 installed. To use the grinder with the included 

grounds bin instead, pull the PortaHolder straight out and replace it with the grounds bin.
a.  The PortaHolder arms can be adjusted up or down to accommodate different sizes of 

portafilters. To adjust the PortaHolder arms:
i. 

Pull the PortaHolder out of the grinder.

ii.  With a Phillips head screwdriver, loosen the two screws in the back of the PortaHolder.
iii.  Move the PortaHolder arms up or down so that the portafilter fits. If the arms are 

difficult to move, loosen the screws further.

iv.  While holding the arms in position, tighten the two screws to lock the arms into place.

5.  Plug in the grinder. The display should illuminate and go through its startup process.
6.  Reference the grind settings chart on page 7 and use the micro adjustment 

(5)

 and macro 

adjustment 

(6)

 arms to select a grind setting.

2

7.  Add beans to the hopper. Ensure bean shut-off knob is turned open. ‘OPEN’ should be facing up 

on the knob.

1

 Installing the hopper with the lid on top may make for easier installation.

2

 Beans between the burrs will cause resistance when adjusting to a finer setting. Make finer adjustments either with the unit running,  

or completely empty of coffee.

Summary of Contents for Vario+














Reviews: