background image

FORTÉ™ AP/BG MANUAL

August, 2022 (v4)

3

SAFETY INFORMATION

Keep these instructions for future reference. Read the information 
below very carefully as it contains important safety information for 
use of this appliance.

 !

Use only with AC current and the correct voltage. See the 
label on the base of the grinder to determine the correct 
voltage.

 !

Only clean the grinder housing with a dry or slightly 
damp cloth. Do not immerse the grinder, plug or cord in 
water or any other liquid.

 !

Baratza will not accept any liability for damage, injury, or 
warranty if the grinder is used other than for its intended 
purpose (i.e. grinding roasted whole coffee beans) or is 
improperly operated or repaired.

 !

Do not operate the grinder with a damaged cord or plug. 
If the supply cord is damaged, it must be replaced by 

the manufacturer, its service agent or similarly qualified 

persons in order to avoid a hazard.

 !

Keep the appliance and its cord out of reach of children 
aged less than 8 years.

 !

Do not leave your grinder unattended while turned ON.

 !

This appliance can be used by children aged from 8 
years and above and persons with reduced physical, 
sensory or mental capabilities or lack of experience 
and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe way 
and understand the hazards involved.

 !

Cleaning and user maintenance shall not be made by 
children without supervision.

 !

Always unplug the grinder from the electrical supply 
before assembling, disassembling or cleaning. To 
unplug, grasp plug and remove from the outlet. Never 
pull on the cord.

CAUTION: ALWAYS unplug the electrical supply cord prior to cleaning the grinder.

Summary of Contents for Forte AP














Reviews: