Bante Instruments BI-650 User Manual Download Page 9

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

The information in this document is subject to change without notice. 

Copyright ©  Bante Instruments Inc, 2022. All rights reserved. 

Disposal 

This product is required to comply with the European Union’s Waste 

Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC and 
may not be disposed of in domestic waste. Please dispose of product 
in accordance with local regulations at the collecting point specified 
for electrical and electronic equipment. 
 

 

 

Warranty 

The warranty period for meter is one year from the date of shipment. 
Above warranty does not cover the electrode and standard solution. 
Out of warranty products will be repaired on a charged basis. 
The warranty on your meter shall not apply to defects resulting from: 

  Improper or inadequate maintenance by customer 

  Unauthorized modification or misuse 

  Operation outside of the environment specifications of the   

 

products

.

   

For more information, please contact the supplier. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Office: 4715 Castlewood St., Sugar land, TX 77479, USA 
Tel: (+1) 346-762-7358 
E-mail: [email protected] 
 
Factory: F3, Building 2, No.2185, Laifang Rd., Shanghai 201615, China 
Tel: (+86) 21-6404-1598 
E-mail: [email protected] 
 

   

www.bante-china.com 

 

Summary of Contents for BI-650










Reviews: