D10
Expert
™
Dual Discrete Outputs
2
P/N 64154 rev. F
Banner Engineering Corp.
•
Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Figure 1. D10 features
dynamic
static
Output
Indicators
Output Select
Indicators
4-Digit
Display
Light/Dark
Operate, Clock
and Lock Icons
Programming
Push Buttons
For emitter and receiver port
locations, see page xx.
Overview
The D10
Expert
Sensor is a high-performance plastic fiber-optic sensor whose many
configuration (TEACH-mode) options make it suitable for demanding applications. Even with
all its features, it is extremely easy to use. Advanced 16-bit microcontroller technology makes
this possible.
The D10
Expert
provides high-performance sensing in low-contrast applications.
Expert
TEACH and setup options provide static, dynamic and single-point programming plus manual
fine adjustment, remote programming and push button lockout. Its slender, stylized housing
has a large digital display visible beneath a clear cover for easy programming and status
monitoring during operation. The sensor mounts directly to standard 35 mm DIN rail or using
the supplied mounting bracket.
The sensor features two outputs with independent setpoints: either NPN or PNP, depending
on model. Built-in crosstalk avoidance protocol provides trouble-free operation for multiple
sensors in one area.
Light/Dark
Operate Selection
Toggle to select the condition for which each output will conduct: when the target is present or when the target is absent.
OFF-Delay Timing
Selection
Programmable OFF-delay pulse stretcher: 0, 2, 5, 10, 15, 20, 30, 40, 60, 80, or 100 milliseconds
Display Selection
Discrete Output: Raw signal value or % excess signal
Power Level/
Speed Selection
Super High-Speed† (SHS)
High-Speed (HS)
High-Power (HP)
Super High-Power (SHP)
Response*
50 µs
200 µs
1 ms
2.5 ms
Repeatability
25 µs
50 µs
75 µs
100 µs
Maximum
Range*
Fiber
Red 680 nm
Green 525 nm
Red 680 nm
Green 525 nm
Red 680 nm
Green 525 nm
Red 680 nm
Green 525 nm
PIT16U
20 mm
9 mm
30 mm
9 mm
55 mm
13 mm
90 mm
16 mm
PIT26U
100 mm
40 mm
150 mm
40 mm
250 mm
55 mm
400 mm
70 mm
PIT46U
300 mm
100 mm
550 mm
100 mm
1000 mm
160 mm
1200 mm
180 mm
PIT66U
600 mm
180 mm
1000 mm
180 mm
1700 mm
280 mm
2400 mm
320 mm
PBT16U
6 mm
**
10 mm
**
18 mm
3 mm
30 mm
3.5 mm
PBT26U
30 mm
12 mm
50 mm
12 mm
100 mm
20 mm
150 mm
25 mm
PBT46U
100 mm
30 mm
175 mm
30 mm
250 mm
42 mm
300 mm
60 mm
PBT66U
175 mm
55 mm
250 mm
55 mm
400 mm
80 mm
475 mm
100 mm
Tracking Feature
Sets Output 2 to identical settings as Output 1; Output 2 settings can then be revised as desired. (See Advanced Setup procedure, page 11.)
Factory Default
Settings
The following settings are preset at the factory; revert sensor to factory defaults using Advanced Setup procedure (page 11).
• Light operate (LO)
• Output 1 displayed
• Maximum power setting
• No OFF-delay (t 0)
• High Speed (HS); 200 µs response
• Discrete: switchpoint positioned at middle of range
• Raw signal value (1234)
* Diffuse mode performance based on 90% reflectance white test card.
** ø0.010" bifurcated fiber not recommended in these speed settings. Contact Banner Applications for more information.
† See note on page 10.
