B&R 2100, User Manual

Page: 219 / 268

Software • RFID command set
Chapter 4 Software
Panel PC 2100 swing arm user's manual V1.12 219
Command Description Parameter 1 Parameter 2 Parameter 3 Parameter 4 Parameter 5
Show_SN Displays the active tag number -- -- -- -- --
Show_Key Displays the active key -- -- -- -- --
Echo_On Displays an input echo for the output -- -- -- -- --
Echo_Off Suppresses the input echo for the output (default) -- -- -- -- --
Startup Displays the startup message -- -- -- -- --
Life Life command --> Returns OK -- -- -- -- --
Helpme Displays a list of all commands -- -- -- -- --
Show_Error Shows error details -- -- -- -- --
Table 216: General commands
16.2.6 Update commands
Command Description Parameter 1 Parameter 2 Parameter 3 Parameter 4 Parameter 5
Restart Restarts the reader -- -- -- -- --
Firmware_Update Switches the µC to X-modem update mode -- -- -- -- --
Firmware_Upgrade Switches the µC to USB mass memory update mode -- -- -- -- --
Firmware_Info Displays information about the current firmware -- -- -- -- --
Table 217: Update commands
16.2.7 MIFARE commands
Command Description Parameter 1 Parameter 2 Parameter 3 Parameter 4 Parameter 5
Read Reads a 16-byte block from PICC "A" or "B" See table " Ac-
cess
rights " (para-
meter 2).
Source block -- --
Read_Blocks Reads the specified range of blocks from PICC "A" or "B" See table " Ac-
cess
rights " (para-
meter 2).
Starting block Ending block --
Write Writes a 16-byte block to PICC "A" or "B" See table " Ac-
cess
rights " (para-
meter 2).
Destination
block
16-byte data in
hex 00h
--
Decr Takes the value of the source value block, subtracts the
specified value and writes the result to the destination
block
"A" or "B" See table " Ac-
cess
rights " (para-
meter 2).
Source block Destination
block
Value
Incr Takes the value of the source value block, adds the
specified value and writes the result to the destination
block
"A" or "B" See table " Ac-
cess
rights " (para-
meter 2).
Source block Destination
block
Value
Restore Copies a value block "A" or "B" See table " Ac-
cess
rights " (para-
meter 2).
Source block Destination
block
--
InitZero Initializes a value block with the value 0 "A" or "B" See table " Ac-
cess
rights " (para-
meter 2).
Destination
block
-- --
Store_Key_EEPROM Stores a 6-byte key in EEPROM "A" or "B" Sector for key
in reader's
EEPROM
6-byte key
Store_Key_Temp Stores a 6-byte key in the µC temporarily until switched
off
6-byte key -- -- -- --
Connect Connects manually to a specific tag 4-byte SNr -- -- -- --
Disconnect Automatically restores a connection to the best tag -- -- -- -- --
Key_CMD Sends a key directly with each command (default) -- -- -- -- --
Key_EEPROM Uses the key from EEPROM -- -- -- -- --
Key_TEMP Uses the temporary key -- -- -- -- --
Table 218: MIFARE commands
16.2.8 MIFARE commands - Examples
Writing data to block 5 with key A from the reader's EEPROM sector 0:
write,a,0,5,0123456789ABCDEF0123456789ABCDEF
Response:
Command write ->
Data in sector 1 Block 5 written=0123456789ABCDEF0123456789ABCDEF