background image

BA24

26

UK

BA24 / AS05100

Electronic control unit  for the automation of one 

or two motors - 24V dc -  for swinging and sliding gates,

 overhead garage doors and barriers 

230Vac monophase 50/60 Hz

1 or 2

24 Vdc

24Vdc 10W max

24Vdc 3W max

24Vdc 8W max 

including safety device power supply

24Vdc 8W max including accessories power supply

Plug-in

-20°C +60°C

Control unit

Type

Power supply
N° motors
Motor power supply
Flashing light
Warning light

Accessories power supply

Safety device power supply

Radio receiver
Operating temperature

TECHNICAL SPECIFICATIONS /  FUNCTIONS

• Red warning LEDs of N.C. contacts. There isn't the safety devices LED; the possible anomaly is indicated by 

the writing SAF on the LCD.

• Green warning LEDs of N.A. contacts. 
• Two electrical locks management. 
• Safety test run before the opening and closing movement.
• Photocell 1 test run before the opening and closing movement.
• Amperometric circuit test run before the opening and closing movement.
• Stop  and  motion  inversion  for  2  seconds  after  intervention  of  the  safety  devices. At  the  next  Start  pulse  the 

motion restarts in the obstacle freeing direction.

• SEPARATE  SAFETY  DEVICES  POWER  SUPPLY  Connect  the  safety  devices  that  must  be  tested  to  this 

clamp.

Digital programming of all functions.
• Working time adjustable independently in opening and closing for each single motor.
•  Deceleration  time  adjustable   independently  in  opening  and closing  for each  single  motor  in  the final  motion 

phase.

• Gate phase shift time adjustable  independently in opening and closing.
• Adjustable pedestrian working time.
• Pause time adjustable  and differentiated for complete or pedestrian opening.
• Thrust force adjustable  on 10 levels for each motor.
• Decelerations selectable and adjustable  independently on 10 levels for each motor.
• Absorption  (anti-crushing)  control  adjustable  on  100  levels for  each  single motor  both  in  thrust  phase  and  in 

deceleration phase.

• Deceleration enable modes: with single or double limit switch.
• 4 possible working functions (step-by-step, step-by-step with stop, condominium or automatic, dead-man).
• Possibility  of  choosing  the  system    configuration  from  swing  gate  (single  or  double),  overhead/barrier  and 

sliding gate (single or double).

Summary of Contents for G:B:D: AS05100





























Reviews: